-
{{Languages|Manually using GSM}}
This is a short guide how to manually get GSM going.
4 KB (709 words) - 07:40, 19 July 2009
-
To use NAP you'll need to create bridge device manually with
...ed and even after suspend when the bt device get's disconnected, it can be manually reconnected via dbus call (see bellow) -- Vanous</i>. -- PaulFertser
36 KB (5,665 words) - 15:53, 24 July 2010
-
That should be it. Now you can use 'ifup ppp0' and 'ifdown ppp0' manually too.
* [[Manually using GSM]]
17 KB (2,747 words) - 13:17, 27 August 2010
-
...If you have trouble using cu, you may want to refer to the article about [[manually using GSM]] for more information.
...pping gsmd is sufficient. Again, if you have any problems, refer to the [[manually using GSM]] article for additional setup details.
8 KB (1,335 words) - 09:47, 19 July 2009
-
3 KB (560 words) - 15:21, 28 November 2008
-
4 KB (710 words) - 08:14, 9 December 2009
-
This page explains how you can manually re-flash the [[U-Boot]] into your Neo1973. It is basically the manual task
3 KB (468 words) - 09:23, 10 February 2012
-
547 B (89 words) - 05:23, 21 July 2009
-
...спользовании cu, you may want to refer to the article about [[manually using GSM]] for more information.
...кнут затруднения, обращайтесь к статье [[manually using GSM]] за дополнительными деталями настр
13 KB (604 words) - 21:33, 12 September 2008
-
Can I input KI,IMSI&ICCID codes manually to use the phone without (or with many) sim-cards?
91 B (17 words) - 14:23, 29 January 2008
-
=== Using it manually ===
=== Manually using GPRS ===
4 KB (527 words) - 21:37, 12 September 2008
-
33 B (5 words) - 20:34, 15 August 2008
-
9 KB (1,542 words) - 08:38, 9 September 2008
-
#REDIRECT [[Manually re-flashing the u-boot]]
45 B (5 words) - 08:38, 10 February 2012
-
It provides a human-readable telnet interface for manually halting/resuming the target device, reading/writing registers and memory, e
8 KB (1,208 words) - 16:43, 10 February 2013
-
The pages linked above are all maintained manually. We also maintain an automatic categorization system by tagging wiki pages.
22 KB (3,343 words) - 11:41, 12 January 2012
-
...of all the applications that can be upgraded. It's still up to the user to manually check the applications they want to upgrade. After pressing the apply butto
5 KB (854 words) - 21:22, 27 June 2007
-
...recipes it could even tell you what to buy without entering a shoppinglist manually.
...a rather longwinded repeating of numbers to each other, or half the people manually inputting numbers before phoning/texting the other half to complete the pro
105 KB (17,388 words) - 17:47, 11 May 2010
-
...G option for it, so if you're not using the -moko kernel tree, you have to manually patch the s3c2410 nand driver to enable the BBT option.
12 KB (1,951 words) - 08:28, 10 February 2012
-
{{Languages|Manually using GSM}}
This is a short guide how to manually get GSM going.
4 KB (709 words) - 07:40, 19 July 2009
-
* [[Manually using GSM]]
* [[Manually using GPRS]]
606 B (74 words) - 19:48, 22 October 2008
-
Manually issue
you can manually override the charging mode via sysfs or in u-boot, if
8 KB (1,239 words) - 08:32, 10 February 2012
-
::The GPS device [[Manually using GPS|outputs the altitude]] as well. This has been tested and works fi
56 KB (9,304 words) - 13:52, 6 April 2011
-
... to [[MokoMakefile]]. However, if you do have the build environment set up manually and you're sure you know what you're doing, then feel free to go forward wi
15 KB (2,305 words) - 21:52, 12 September 2008
-
...n use with Debian (ext2) on it (Qtopia on flash). It can only be boot with manually from NAND. Suspending still causes I/O error on the SD. The rest seems stab
3 KB (576 words) - 14:47, 28 October 2009
-
To use NAP you'll need to create bridge device manually with
...ed and even after suspend when the bt device get's disconnected, it can be manually reconnected via dbus call (see bellow) -- Vanous</i>. -- PaulFertser
36 KB (5,665 words) - 15:53, 24 July 2010
-
...lds, or you can go into the fso-testing directory and run bitbake commands manually. The choice is yours.
...ollowing script should remove all non-essential variables; you should also manually trim your path to the minimum.
16 KB (2,535 words) - 20:27, 3 September 2009
-
==== How do I get Bluetooth working manually? ====
34 KB (5,408 words) - 08:30, 10 February 2012
-
List pages are manually maintained lists of links to a certain set of articles. Their purpose is si
15 KB (2,400 words) - 09:24, 19 August 2010
-
... then you need tell the package manager to update them, or you can do that manually with
35 KB (5,125 words) - 08:42, 10 February 2012
-
...o make it through this part of the build by applying the remaining patches manually. --[[User:Mellon|Ted Lemon]] 15:44, 29 July 2007 (CDT)
36 KB (5,428 words) - 08:37, 10 August 2009
-
Then you manually set the IP address of the USB to 192.168.0.200
An alternative way is to do it manually:
10 KB (1,686 words) - 16:58, 24 September 2011
-
==Reflashing the neo1973 manually==
This is how to manually do the above. It may be outdated, perhaps dangerously so.
9 KB (1,378 words) - 08:40, 10 February 2012
-
The current profile could be selected manually, or automatically depending on time of day or possibly even the GPS locatio
3 KB (492 words) - 12:18, 31 August 2008
