Search results
From Openmoko
- Little tool to write notes using pen and touchscreen. This program is written in [[Python]] using pygtk. It can be used only if those are present in your environment (see [[3 KB (405 words) - 20:54, 18 October 2008
- However, using the u-boot console you can manually enable fast charging. See [[U-boot#Battery_charger_related]] for more infor usb0: full speed config #1: 500 mA, Ethernet Gadget, using CDC Ethernet15 KB (2,428 words) - 09:44, 12 January 2010
- Calls can be placed using the graphical [[Dialer]] or the textual [http://wiki.openmoko.org/wiki/Gsmd ...needs to be done on the command-line [[manually using GSM]] and [[manually using GPRS]], until [[gsmd]] supports more.3 KB (482 words) - 21:42, 16 September 2008
- ...ave a look in gsmd logs or use the instructions detailed in the [[Manually using GSM]] page and issue the ''AT+CIMI'' command. However, using the u-boot console you can manually enable fast charging. See [[U-boot#Battery_charger_related]] for more infor14 KB (2,049 words) - 09:43, 12 January 2010
- ''See [[manually using GPRS]].'' ''See [[manually using Bluetooth]].''1 KB (193 words) - 11:04, 7 September 2008
- ...arty. You can either depend on network decision ("By network") or force it manually ("Manual") If you like to test a .sid you can play it using this command on the FR:55 KB (3,991 words) - 09:23, 17 October 2010
- ...so the program watches /dev/nmeaNP instead. You will need to launch gllin manually. * gllin MUST be started manually (execute "gllin" from terminal)9 KB (1,250 words) - 22:58, 22 August 2008
- ***If you are using dd from coreutils: ***If you are using dd from busybox (Interrupt the process (ctrl+c) once the file is big enough7 KB (1,083 words) - 22:01, 29 June 2010
- ...ьзовании cu, you may want to refer to the article about [[manually using GSM]] for more information. ... затруднения, обращайтесь к статье [[manually using GSM]] за дополнительными деталями настройк13 KB (604 words) - 21:33, 12 September 2008
- ...o use bluetooth to transfer data between Neo and Desk-top]] and [[Manually using Bluetooth]]. ...4] After connecting using the GUI, you may also need to run "udhcpc eth0" manually in the terminal to get DNS entries added to your resolv.conf. You may also9 KB (1,260 words) - 12:08, 5 November 2009
- ... fast 1000 mA charge "touch /home/root/allow_force_1000" I don't recommend using this one If you want to run checkFastCharge manually, without the /etc/init.d script...8 KB (1,262 words) - 08:01, 10 February 2012
- to handle reconnects manually.1 KB (240 words) - 08:42, 10 February 2012
- ...rop-down & correct them as necessary than to type all your contact info in manually on the neo keyboard, which was my option before I wrote this :-) Using the Neo on-screen keyboard type (or source a script):3 KB (544 words) - 16:17, 19 July 2009
- 1. What NEO device you are using? [[GTA01]] or [[GTA02]]. ...at is your GSM firmware version? You can get this number by an AT command. Using [[USB_Networking|SSH]] to connect to your NEO, then type these commands:9 KB (1,289 words) - 10:29, 16 November 2009
- To manually restore one of the state files, '''Question: I am using headphones but only the right speaker work the left don't work how can I fi15 KB (2,295 words) - 13:59, 23 September 2011
- |SPI || Works || The guest kernel can drive it using either the SPI interface or raw GPIO bitbanging. ...s in GPIO wiring. Hardware emulation is implemented in a clean-room manner using official specifications where possible.34 KB (4,772 words) - 17:01, 23 February 2009
- If no context rules are defined the profile can only be activated manually and will remain in force until context awareness turned back on or another4 KB (608 words) - 22:24, 30 August 2008
- |SPI || Works || The guest kernel can drive it using either the SPI interface or raw GPIO bitbanging. ...s in GPIO wiring. Hardware emulation is implemented in a clean-room manner using official specifications where possible.31 KB (4,439 words) - 22:04, 12 September 2008
- '''GPRS''': См. [[Manually using GPRS]] '''Bluetooth''': См. [[Manually using Bluetooth]]38 KB (1,008 words) - 09:28, 12 January 2010
- = Building manually = ...n files you would create manually. So I just don't get why people say that using a Makefile doesn't tell you much about what is going on under the hood. I5 KB (761 words) - 13:28, 7 February 2009