User talk:Gabrys
From Openmoko
Contents |
Testing GSM <-> BT
Basics: We need to tell audio codec to route sound from GSM chip to BT chip. Codec is controlled by ALSA and mixer settings.
Prerequisites: BT device must be paired before the operation.
Step one: powering on bluetooth, setting up bluetoothd, pairing
Set /etc/bluetooth/audio.conf like this:
# SCO routing. Either PCM or HCI (in which case audio is routed to/from ALSA) # Defaults to HCI SCORouting=PCM
Then
echo 1 > /sys/bus/platform/devices/neo1973-pm-bt.0/power_on hciconfig hci0 up bluetoothd
then use simple-agent from here: http://wiki.openmoko.org/wiki/Manually_using_Bluetooth#Pair to pair the device.
Test: "hcitool con" should say:
Connection ACL 00:13:17:78:7B:A3 handle 0 state 5 lm MASTER
Test2:
BTADAPTER=`dbus-send --system --dest=org.bluez --print-reply / org.bluez.Manager.DefaultAdapter | tail -1 | sed 's/^.*"\(.*\)".*$/\1/'` dbus-send --system --dest=org.bluez --print-reply $BTADAPTER/dev_00_13_17_78_7B_A3 org.bluez.Headset.Connect
should say: Error org.bluez.Error.AlreadyConnected: Already Connected
More debug
root@om-gta02 /usr/lib/python2.6/site-packages $ dbus-send --system --dest=org.bluez --print-reply $BTADAPTER/dev_00_13_17_78_7B_A3 org.bluez.Headset.Disconnect method return sender=:1.18 -> dest=:1.287 reply_serial=2 root@om-gta02 /usr/lib/python2.6/site-packages $ dbus-send --system --dest=org.bluez --print-reply $BTADAPTER/dev_00_13_17_78_7B_A3 org.bluez.Headset.Connect Error org.bluez.Error.ConnectionAttemptFailed: Input/output error root@om-gta02 /usr/lib/python2.6/site-packages $ dbus-send --system --dest=org.bluez --print-reply $BTADAPTER/dev_00_13_17_78_7B_A3 org.bluez.Headset.Connect method return sender=:1.18 -> dest=:1.290 reply_serial=2 root@om-gta02 /usr/lib/python2.6/site-packages $ dbus-send --system --dest=org.bluez --print-reply $BTADAPTER/dev_00_13_17_78_7B_A3 org.bluez.Headset.Play method return sender=:1.18 -> dest=:1.292 reply_serial=2
Step two: make a call
Call to the phone and answer (or place a call, whichever is cheaper).
Step three: load ALSA settings to switch codec "mode" to GSM <=> BT
Wait till frameworkd sets its statefile and then overwrite it with your own:
alsactl restore < /path/to/the/statefile
(Find working statefile first)
Then due to kernel bug, do:
amixer sset "Capture Left Mixer" "Analogue Mix Right" amixer sset "Capture Left Mixer" "Analogue Mix Left"
Then issue dbus call (check what it is exactly) this starts exchanging audio between GSM and BT (hopefully):
BTADAPTER=`dbus-send --system --dest=org.bluez --print-reply / org.bluez.Manager.DefaultAdapter | tail -1 | sed 's/^.*"\(.*\)".*$/\1/'` dbus-send --system --dest=org.bluez --print-reply $BTADAPTER/dev_00_13_17_78_7B_A3 org.bluez.Headset.Play
We would also need to set bluetooth IIS to 8000 rate:
import alsaaudio pcm_play = alsaaudio.PCM( alsaaudio.PCM_PLAYBACK, alsaaudio.PCM_NONBLOCK, "hw:0,1" ) pcm_play.setchannels(1) pcm_play.setrate(8000) pcm_play.setformat(alsaaudio.PCM_FORMAT_S16_LE) pcm_play.setperiodsize(500000) pcm_cap = alsaaudio.PCM( alsaaudio.PCM_CAPTURE, alsaaudio.PCM_NONBLOCK, "hw:0,1" ) pcm_cap.setchannels(1) pcm_cap.setrate(8000) pcm_cap.setformat(alsaaudio.PCM_FORMAT_S16_LE) pcm_cap.setperiodsize(500000)
We should hear something in the BT headset and not in phone's speaker.