Specialized USB cables
From Openmoko
(sorted out structure; now to fill in content) |
(→How to make a mini type B plug to a type A jack cable) |
||
Line 11: | Line 11: | ||
=== How to make a mini type B plug to a type A jack cable === | === How to make a mini type B plug to a type A jack cable === | ||
− | (picture) | + | (picture, as soon as I build it) |
− | + | Parts list: | |
− | + | ||
− | + | * Mini type B plug: Digi-Key Part Number H2958-ND | |
− | + | * type A jack: I have not yet been able to find a source for these. Meanwhile, use the jack from a standard USB extension cord e.g. | |
+ | * Cable: Ideally, the data lines should be twisted and 28 AWG, the power lines should be 20 or 28 AWG, e.g. part number 49248 from Hitachi Cable [[http://www.hcm.hitachi.com/electronic_round_cable/bulk-usb-cable.shtml]] | ||
+ | |||
+ | Construction instructions: | ||
+ | |||
+ | (TBA) | ||
+ | |||
+ | === Ready-made mini type B plug to a type A jack cable === | ||
+ | |||
+ | [[http://www.jaykang.com/usbafetousbm1.html]] | ||
+ | USB A-Type Female to USB Mini-B Type 5 Pin Male Adapter | ||
+ | http://us.st12.yimg.com/us.st.yimg.com/I/yhst-25796116032680_2011_55823488 | ||
+ | |||
+ | http://www.jaykang.com/usbtyfetotyf.html | ||
+ | USB Type A Female to Female Gender Changer | ||
+ | http://us.st12.yimg.com/us.st.yimg.com/I/yhst-25796116032680_2011_56525956 | ||
=== How to make a type B jack to a type A jack adapter (gender changer) === | === How to make a type B jack to a type A jack adapter (gender changer) === |
Revision as of 08:49, 30 August 2008
NOTE: work in progress |
Contents |
Attaching the Neo (acting as a USB host) to a USB device
The USB port (5 position mini type B jack) on the Neo 1973 and Neo FreeRunner can be both a USB device or a USB host. The provided cable (5 position mini type B plug to type A plug) is used when attaching the Neo to a USB host.
A specialized cable is required when attaching the Neo to a USB device.
Alternately, an adapter capable of connecting two type A plugs will allow attaching the provided USB cable to the USB cable that came with the USB device. This adapter is also known as a gender changer. These can be purchased or made.
How to make a mini type B plug to a type A jack cable
(picture, as soon as I build it)
Parts list:
- Mini type B plug: Digi-Key Part Number H2958-ND
- type A jack: I have not yet been able to find a source for these. Meanwhile, use the jack from a standard USB extension cord e.g.
- Cable: Ideally, the data lines should be twisted and 28 AWG, the power lines should be 20 or 28 AWG, e.g. part number 49248 from Hitachi Cable [[1]]
Construction instructions:
(TBA)
Ready-made mini type B plug to a type A jack cable
[[2]] USB A-Type Female to USB Mini-B Type 5 Pin Male Adapter http://us.st12.yimg.com/us.st.yimg.com/I/yhst-25796116032680_2011_55823488
http://www.jaykang.com/usbtyfetotyf.html USB Type A Female to Female Gender Changer http://us.st12.yimg.com/us.st.yimg.com/I/yhst-25796116032680_2011_56525956
How to make a type B jack to a type A jack adapter (gender changer)
This community provided instruction shows how to build an adapter from a USB socket salvaged from a computer motherboard.
Note that these instructions are provided in the hope that they are useful but without any warranty!
- Find an old motherboard with a set of two USB receptacles as shown above.
- Desolder this set of receptacles from the motherboard. This can be bit tricky but it is doable at least with a desoldering gun.
- Each receptacle has four pins. Use a multimeter to verify that you have no short circuits between the pins or the shield.
- Solder adjacent pins together (GND to GND, D- to D-, D+ to D+, VCC to VCC).
- (Optional) Build a test cable. Cut an USB cable with A plug into half, connect it a receptacle and again measure that you have no short circuits. Then connect the test cable to PC and verify that you see
black GND green 0V white 0V red +5V
- Freerunner is shipped with a mini-B-to-A-plug cable. Connect this to a receptacle.
- (Optional)Connect test cable to the other receptacle and verify that you see
black GND green 0V white 0V red 0V
when freerunner acts as a device and
black GND green 0V white 0V red +5V
when it acts as a host.
- At your own risk, switch freerunner to USB host mode and connect an USB device to the other receptacle of the adapter. Here's how the setup should look like:
Compatibility
The adapter works with kingston data traveller 4G memory stick and aiptec pencam webcam. However, for some reason (probably the missing 15k resistors at D+ and D-) it did not work with any of the tested USB keyboards or mice:
usb 1-2: new full speed USB device using s3c2410-ohci and address 24 usb 1-2: device descriptor read/64, error -62 usb 1-2: device descriptor read/64, error -62 usb 1-2: new full speed USB device using s3c2410-ohci and address 25 usb 1-2: device descriptor read/64, error -62 usb 1-2: device descriptor read/64, error -62 usb 1-2: new full speed USB device using s3c2410-ohci and address 26 usb 1-2: device not accepting address 26, error -62 usb 1-2: new full speed USB device using s3c2410-ohci and address 27 usb 1-2: device not accepting address 27, error -62
However, if I connect neo to small (unpowered) USB hub
usb 1-2: new full speed USB device using s3c2410-ohci and address 61 usb 1-2: configuration #1 chosen from 1 choice hub 1-2:1.0: USB hub found hub 1-2:1.0: 4 ports detected
and connect the keyboard to the hub then it is correctly recognized:
usb 1-2.3: new low speed USB device using s3c2410-ohci and address 62 usb 1-2.3: configuration #1 chosen from 1 choice input: USB Keyboard as /devices/platform/s3c2410-ohci/usb1/1-2/1-2.3/1-2.3:1.0/input/input13 input: USB HID v1.10 Keyboard [ USB Keyboard] on usb-s3c24xx-2.3 input: USB Keyboard as /devices/platform/s3c2410-ohci/usb1/1-2/1-2.3/1-2.3:1.1/input/input14 input: USB HID v1.10 Device [ USB Keyboard] on usb-s3c24xx-2.3
With the hub I can also use both keyboard and usb memory stick at the same time.
Power consumption
When I unplug the USB hub (with only keyboard connected to it) the power consumption estimate at /sys/devices/platform/bq2700-battery.0/power_supply/bat/current_now decreases from 175000 to 145000 (are these microamperes?).
How to make a USB cable for powering attached USB devices and charging the Neo while in host mode
This cable might be necessary for a number of reasons, e.g.
- The application requires that the Neo not become suspended
- The application requires long run time
- The attached USB device consumes a lot of power
These instructions will show you how to make a cable with 3 ends:
- A mini-USB type B cable for the Neo itself
- A cable of whatever type to go to your USB device.
- A cable going to a +5V +/-10%(max!) power supply with enough power for your device and to charge the Neo. This could be a wall charger or even another USB plug.
You connect the Data+ and Data- wires of the Neo and the device, and connect all of the ground wires together and all of the +5V wires together. This powers the Neo and the device, while letting the neo talk to the device. You have to connect 2pcs 15kOhm resistors, one from D+ to ground, and one from D- to ground, to comply with USB-spec for hostmode, as Neo is switching off the internal resistors when you enable charging/powering over USB by asserting EN_USBHOST. See schematics, LOCATION:49XX
Just for reference, the USB wires from left to right are:
- Black: Power -
- Green: Data -
- White: Data +
- Red: Power +
The Mini_USB-B connector has a fifth pin, the ID-pin. This pin is supposed to be short to ground to signal Freerunner to enter hostmode. For the Y-cable and enabling external power while in hostmode, you may connect a 47kOhm resistor from ID-pin to ground. This is the same trick the OM-wallcharger uses to signal to Freerunner it can charge with 1A. Future kernels should switch to hostmode + external power when seeing this 47k resistor.