-
30 B (3 words) - 22:03, 3 August 2009
-
39 B (5 words) - 09:19, 12 January 2010
-
33 B (4 words) - 09:37, 12 January 2010
-
33 B (4 words) - 09:40, 12 January 2010
-
39 B (5 words) - 09:18, 12 January 2010
-
39 B (5 words) - 09:19, 12 January 2010
-
33 B (4 words) - 09:44, 12 January 2010
-
36 B (5 words) - 09:43, 12 January 2010
-
36 B (4 words) - 22:25, 27 August 2009
-
30 B (3 words) - 09:42, 10 February 2012
-
39 B (5 words) - 09:21, 12 January 2010
-
33 B (4 words) - 09:33, 12 January 2010
-
33 B (4 words) - 09:41, 12 January 2010
-
33 B (4 words) - 09:42, 12 January 2010
-
39 B (5 words) - 09:19, 12 January 2010
-
39 B (5 words) - 11:30, 29 November 2009
-
39 B (5 words) - 09:17, 12 January 2010
-
39 B (5 words) - 09:15, 12 January 2010
-
39 B (5 words) - 09:18, 12 January 2010
-
39 B (5 words) - 09:18, 12 January 2010
-
...chain from the Openmoko project. On this page you can find a recipe to get started with this toolchain leading you through a series of steps to compile a proj
==Getting your application packaged by OE==
18 KB (2,634 words) - 19:55, 6 July 2010
-
...the service is not running when a message is sent, the application will be started.
*a session bus which is started for the user when X starts
2 KB (341 words) - 10:48, 12 September 2009
-
...ww.freeswitch.org/ Freeswitch] is also well worth a look -- it's a project started by a long time contributor to Asterisk, and seems to be more scalable on si
105 KB (17,388 words) - 17:47, 11 May 2010
-
* '''2009-05-07''' writing of Kustomizer for OM2009 started at [http://etherpad.com/zt3x1x7ERX Etherpad]
# (new) Kustomizer mailing list started: joing by mailing kustomizer+subscribe@googlegroups.com
17 KB (2,506 words) - 17:54, 16 November 2009
-
gsmd is usually started as a background daemon when booting by the /etc/init.d/gsmd script, in this
...allowing the host PC to interact directly with the modem. Some notes about getting gsmd running in this manner is [[User:Miki/hosted_gsmd|here]].
10 KB (1,533 words) - 16:19, 8 February 2010
-
The BBT is created once a BBT-implementing u-boot is started for the first time. The BBT scanning code assumes that the NAND is '''comp
... parallel-port based JTAG adaptors. Also, the overall flashing process is getting quite complicated. sjf2410-linux could thus only be used for flashing the b
12 KB (1,951 words) - 08:28, 10 February 2012
-
* [[Getting Started with your Neo1973]]
606 B (74 words) - 19:48, 22 October 2008
-
* As soon as pand is started on the phone configure your IP address
...ntis]] 18:37, 15 October 2008 (UTC) Note for use on OpenSuse 11.0 - I was getting a connection failure with 'Host is down(112)' errors in /var/log/messages (
36 KB (5,665 words) - 15:53, 24 July 2010
-
MokoMakefile does not install anything into your system (it can and should be started as normal user). MokoMakefile is a wrapper around all that is required to m
As the QEMU-based neo1973 emulator is also built as part of the build process started by MokoMakefile, so you need gcc-3.3 and other packages for building QEMU i
16 KB (2,535 words) - 20:27, 3 September 2009
-
== Getting Started with your Neo FreeRunner == <!-- Do not rename section! This section is lin
See [[Getting_Started_with_your_Neo_FreeRunner|Getting Started with your Neo FreeRunner]]
34 KB (5,408 words) - 08:30, 10 February 2012
-
Like it's said in the "Getting started with FreeRunner" wiki page, you have to install the full qwerty keyboard, s
11 KB (1,764 words) - 09:14, 23 May 2011
-
...o get Linux up quickly. More information can be found in the [[FAQ]] and [[Getting Openmoko working on host with Xoo|here]].
...''' be used for, and probably no other emulator can, is speed measures and getting the general feel of Openmoko performance. Code running in qemu runs with th
35 KB (5,125 words) - 08:42, 10 February 2012
-
...irect booting from a USB device. Around 2001, PC motherboard manufacturers started to add USB boot support.
13 KB (1,960 words) - 12:23, 31 August 2008
-
This is an indication that the setup process has started. Note that the
9 KB (1,378 words) - 08:40, 10 February 2012
-
* <tt>pstree -Gupl</tt> output after all standard processes have started
32 KB (3,433 words) - 12:23, 31 August 2008
-
* [[Getting Openmoko/ru|Getting Openmoko]]
* [[Getting Started with your Neo FreeRunner/ru | Neo FreeRunner getting started guide]]
16 KB (1,036 words) - 20:16, 8 April 2010
-
*[[Getting Started with your Neo FreeRunner/zh cn|Neo FreeRunner使用手冊]]
8 KB (731 words) - 02:24, 17 January 2010
-
A: This should get you started:
13 KB (2,003 words) - 17:02, 30 August 2008
-
==== Getting started ====
13 KB (1,671 words) - 22:32, 20 August 2008
-
* [[Getting Openmoko|Openmoko besorgen]]
* [[Getting Started with your Neo FreeRunner/de | Neo FreeRunner Anfänger Referenz]]
4 KB (481 words) - 11:03, 26 October 2010
