Revision as of 21:38, 6 April 2010

Testing GSM <-> BT

Basics: We need to tell audio codec to route sound from GSM chip to BT chip. Codec is controlled by ALSA and mixer settings.

Prerequisites: BT device must be paired before the operation.

Step one: powering on bluetooth, setting up bluetoothd, pairing

Set /etc/bluetooth/audio.conf like this:

# SCO routing. Either PCM or HCI (in which case audio is routed to/from ALSA)   
# Defaults to HCI                                                               
SCORouting=PCM                                                                  

Then

echo 1 > /sys/bus/platform/devices/neo1973-pm-bt.0/power_on
hciconfig hci0 up
bluetoothd

then use simple-agent from here: http://wiki.openmoko.org/wiki/Manually_using_Bluetooth#Pair to pair the device.

Test: "hcitool con" should say:

Connection
     ACL 00:13:17:78:7B:A3 handle 0 state 5 lm MASTER

Test2:

dbus-send --system --dest=org.bluez --print-reply $BTADAPTER/dev_00_13_17_78_7B_A3 org.bluez.Headset.Connect

should say: Error org.bluez.Error.AlreadyConnected: Already Connected

More debug

root@om-gta02 /usr/lib/python2.6/site-packages $ dbus-send --system --dest=org.bluez --print-reply $BTADAPTER/dev_00_13_17_78_7B_A3 org.bluez.Headset.Disconnect
method return sender=:1.18 -> dest=:1.287 reply_serial=2

root@om-gta02 /usr/lib/python2.6/site-packages $ dbus-send --system --dest=org.bluez --print-reply $BTADAPTER/dev_00_13_17_78_7B_A3 org.bluez.Headset.Connect
Error org.bluez.Error.ConnectionAttemptFailed: Input/output error

root@om-gta02 /usr/lib/python2.6/site-packages $ dbus-send --system --dest=org.bluez --print-reply $BTADAPTER/dev_00_13_17_78_7B_A3 org.bluez.Headset.Connect
method return sender=:1.18 -> dest=:1.290 reply_serial=2

root@om-gta02 /usr/lib/python2.6/site-packages $ dbus-send --system --dest=org.bluez --print-reply $BTADAPTER/dev_00_13_17_78_7B_A3 org.bluez.Headset.Play   
method return sender=:1.18 -> dest=:1.292 reply_serial=2

Step two: make a call

Call to the phone and answer (or place a call, whichever is cheaper).

Step three: load ALSA settings to switch codec "mode" to GSM <=> BT

Wait till frameworkd sets its statefile and then overwrite it with your own:

alsactl restore < /path/to/the/statefile

(Find working statefile first)

Then due to kernel bug, do:

amixer sset "Capture Left Mixer" "Analogue Mix Right"
amixer sset "Capture Left Mixer" "Analogue Mix Left"

Then issue dbus call (check what it is exactly) this starts exchanging audio between GSM and BT (hopefully):

BTADAPTER=`dbus-send --system --dest=org.bluez --print-reply / org.bluez.Manager.DefaultAdapter | tail -1 | sed 's/^.*"\(.*\)".*$/\1/'`
dbus-send --system --dest=org.bluez --print-reply $BTADAPTER/dev_00_13_17_78_7B_A3 org.bluez.Headset.Play

We would also need to set bluetooth IIS to 8000 rate:

import alsaaudio

pcm_play = alsaaudio.PCM( alsaaudio.PCM_PLAYBACK, alsaaudio.PCM_NONBLOCK, "hw:0,1" )
pcm_play.setchannels(1)
pcm_play.setrate(8000)
pcm_play.setformat(alsaaudio.PCM_FORMAT_S16_LE)
pcm_play.setperiodsize(500000)

pcm_cap = alsaaudio.PCM( alsaaudio.PCM_CAPTURE, alsaaudio.PCM_NONBLOCK, "hw:0,1" )
pcm_cap.setchannels(1)
pcm_cap.setrate(8000)
pcm_cap.setformat(alsaaudio.PCM_FORMAT_S16_LE)
pcm_cap.setperiodsize(500000)

We should hear something in the BT headset and not in phone's speaker.