User:Seanmcneil3

From Openmoko

(Difference between revisions)
Jump to: navigation, search
m (Binutils 2.18)
Line 58: Line 58:
  
 
Warning!!! Installation of Android requires loading a new kernel and rootfs image onto your phone. I have not had time to produce a version that runs completely off an sdcard.
 
Warning!!! Installation of Android requires loading a new kernel and rootfs image onto your phone. I have not had time to produce a version that runs completely off an sdcard.
 +
 +
== Installation ==
 +
 +
As noted above, this installation requires you to wipe out the existing kernel and rootfs in NAND on your Freerunner. You also must have an SDCARD and it needs to be configured with two (2) primary partitions: First is VFAT/MSDOS (16 or 32) which acts as the /sdcard storage area for pictures, movies, music, etc. and the Second is an ext3 primary partition for use of internal Android /data area to store settings, caches, etc.
 +
 +
The first thing I suggest is to setup an SDCARD. You can flash the NAND first, but you must have an SDCARD with two partitions as stated before you'll be able to boot. I use a 2GB card which I have split in half. fdisk shows me:
 +
 +
    /dev/mmcblk0p1              1        2454      996310    6  FAT16<br>
 +
    /dev/mmcblk0p2            2455        4908      996324  83  Linux
 +
 +
formatted as
 +
 +
    sudo mkfs.vfat /dev/mmcblk0p1<br>
 +
    sudo mkfs.ext3 /dev/mmcblk0p2
 +
 +
There is no need to populate the ext3 partition at all. The VFAT partition can be populated with media content if you so desire.
 +
 +
With your SDCARD all set, you are ready to flash the kernel and rootfs:
 +
 +
    sudo {path_to}/dfu-util -d 0x1d50:0x5119 -a kernel -D uImage-android<br>
 +
    sudo {path_to}/dfu-util -d 0x1d50:0x5119 -a rootfs -D androidfs.jffs2<br>

Revision as of 03:53, 5 November 2008

Contents

Android on Freerunner

Google has released their open source version of the Android phone software distribution. In order to use it on the Freerunner, a number of patches need to be applied and a compiler with armv4 java exception support needs to be used to compile the software.


Compiler suite

Android is a little picky about the version of gcc compiler. It also requires some java exception support that isn't available for armv4 without a minor modification. The following tools are what I use to build Android:


Binutils 2.18

At one time I had some armv5t code that was compiled into Android which would cause the linker to generate these blx instructions which fail on armv4. I'm not sure if this is still necessary, but I still have the following change applied to binutils:

diff -urN binutils-2.18-orig/bfd/elf32-arm.c binutils-2.18/bfd/elf32-arm.c
--- binutils-2.18-orig/bfd/elf32-arm.c	2007-08-07 02:59:23.000000000 +0700
+++ binutils-2.18/bfd/elf32-arm.c	2008-03-15 11:30:17.000000000 +0700
@@ -3093,8 +3093,8 @@
 static void check_use_blx(struct elf32_arm_link_hash_table *globals)
 {
   if (bfd_elf_get_obj_attr_int (globals->obfd, OBJ_ATTR_PROC,
-				Tag_CPU_arch) > 2)
-    globals->use_blx = 1;
+				Tag_CPU_arch) >= TAG_CPU_ARCH_V5T)
+    globals->use_blx = 0;
 }
 
 bfd_boolean


configure --prefix={devel path}/android/cross --target=arm-eabi

gcc 4.2.4 with gcc41-java-arm4.patch

configure --prefix={devel path}/android/cross --target=arm-eabi --with-arch=armv4t --enable-shared --enable-threads --disable-nls --disable-libmudflap --enable-target-optspace --with-abi=aapcs --enable-multilib --disable-libssp --disable-libstdcxx --enable-languages=c,c++

java-6-sun

This is the standard Linux package available for most (all?) distributions.

Patches

Coming soon. I've posted a number of them on the devel mailing list so far. Eventually, I expect to provide everything necessary for people to build Android for themselves.

Images

I have placed an older 2.6.26 kernel with Android support at:

  uImage-android

I have put up a jffs2 image that replaces rootfs on the Freerunner at:

  androidfs.jffs2

Warning!!! Installation of Android requires loading a new kernel and rootfs image onto your phone. I have not had time to produce a version that runs completely off an sdcard.

Installation

As noted above, this installation requires you to wipe out the existing kernel and rootfs in NAND on your Freerunner. You also must have an SDCARD and it needs to be configured with two (2) primary partitions: First is VFAT/MSDOS (16 or 32) which acts as the /sdcard storage area for pictures, movies, music, etc. and the Second is an ext3 primary partition for use of internal Android /data area to store settings, caches, etc.

The first thing I suggest is to setup an SDCARD. You can flash the NAND first, but you must have an SDCARD with two partitions as stated before you'll be able to boot. I use a 2GB card which I have split in half. fdisk shows me:

   /dev/mmcblk0p1               1        2454      996310    6  FAT16
/dev/mmcblk0p2 2455 4908 996324 83 Linux

formatted as

   sudo mkfs.vfat /dev/mmcblk0p1
sudo mkfs.ext3 /dev/mmcblk0p2

There is no need to populate the ext3 partition at all. The VFAT partition can be populated with media content if you so desire.

With your SDCARD all set, you are ready to flash the kernel and rootfs:

   sudo {path_to}/dfu-util -d 0x1d50:0x5119 -a kernel -D uImage-android
sudo {path_to}/dfu-util -d 0x1d50:0x5119 -a rootfs -D androidfs.jffs2
Personal tools

Android on Freerunner

Google has released their open source version of the Android phone software distribution. In order to use it on the Freerunner, a number of patches need to be applied and a compiler with armv4 java exception support needs to be used to compile the software.


Compiler suite

Android is a little picky about the version of gcc compiler. It also requires some java exception support that isn't available for armv4 without a minor modification. The following tools are what I use to build Android:


Binutils 2.18

At one time I had some armv5t code that was compiled into Android which would cause the linker to generate these blx instructions which fail on armv4. I'm not sure if this is still necessary, but I still have the following change applied to binutils:

diff -urN binutils-2.18-orig/bfd/elf32-arm.c binutils-2.18/bfd/elf32-arm.c
--- binutils-2.18-orig/bfd/elf32-arm.c	2007-08-07 02:59:23.000000000 +0700
+++ binutils-2.18/bfd/elf32-arm.c	2008-03-15 11:30:17.000000000 +0700
@@ -3093,8 +3093,8 @@
 static void check_use_blx(struct elf32_arm_link_hash_table *globals)
 {
   if (bfd_elf_get_obj_attr_int (globals->obfd, OBJ_ATTR_PROC,
-				Tag_CPU_arch) > 2)
-    globals->use_blx = 1;
+				Tag_CPU_arch) >= TAG_CPU_ARCH_V5T)
+    globals->use_blx = 0;
 }
 
 bfd_boolean


configure --prefix={devel path}/android/cross --target=arm-eabi

gcc 4.2.4 with gcc41-java-arm4.patch

configure --prefix={devel path}/android/cross --target=arm-eabi --with-arch=armv4t --enable-shared --enable-threads --disable-nls --disable-libmudflap --enable-target-optspace --with-abi=aapcs --enable-multilib --disable-libssp --disable-libstdcxx --enable-languages=c,c++

java-6-sun

This is the standard Linux package available for most (all?) distributions.

Patches

Coming soon. I've posted a number of them on the devel mailing list so far. Eventually, I expect to provide everything necessary for people to build Android for themselves.

Images

I have placed an older 2.6.26 kernel with Android support at:

  uImage-android

I have put up a jffs2 image that replaces rootfs on the Freerunner at:

  androidfs.jffs2

Warning!!! Installation of Android requires loading a new kernel and rootfs image onto your phone. I have not had time to produce a version that runs completely off an sdcard.

Installation

As noted above, this installation requires you to wipe out the existing kernel and rootfs in NAND on your Freerunner. You also must have an SDCARD and it needs to be configured with two (2) primary partitions: First is VFAT/MSDOS (16 or 32) which acts as the /sdcard storage area for pictures, movies, music, etc. and the Second is an ext3 primary partition for use of internal Android /data area to store settings, caches, etc.

The first thing I suggest is to setup an SDCARD. You can flash the NAND first, but you must have an SDCARD with two partitions as stated before you'll be able to boot. I use a 2GB card which I have split in half. fdisk shows me:

   /dev/mmcblk0p1               1        2454      996310    6  FAT16
/dev/mmcblk0p2 2455 4908 996324 83 Linux

formatted as

   sudo mkfs.vfat /dev/mmcblk0p1
sudo mkfs.ext3 /dev/mmcblk0p2

There is no need to populate the ext3 partition at all. The VFAT partition can be populated with media content if you so desire.

With your SDCARD all set, you are ready to flash the kernel and rootfs:

   sudo {path_to}/dfu-util -d 0x1d50:0x5119 -a kernel -D uImage-android
sudo {path_to}/dfu-util -d 0x1d50:0x5119 -a rootfs -D androidfs.jffs2