U-Boot/zh cn

From Openmoko

Revision as of 11:22, 2 November 2007 by Sunlt (Talk | contribs)

Jump to: navigation, search
File:Uboot-s3c2410fb.jpg
Neo1973控制台上的u-boot
Neo1973上的u-boot引导菜单

Contents

概述

GTA01使用了u-boot引导装载程序。

关于u-boot的更多信息可以在下列地方找到

但是,未经修改的u-boot不支持GTA01所需要的许多特性,比如

  • 利用S3C2410 Steppingstone从NAND闪存启动
  • 从SD/Transflash读取内核/initrd
  • S3C2410 NAND闪存
  • 通过S3C2410 USB Device控制器下载程序
  • S3C2410 Framebuffer启动logo/状态显示

Harald Welte正在为这些解决问题而工作,并且实际上它们中的大多数已经得到了实现。

引导装载程序源代码

http://svn.openmoko.org/trunk/src/target/u-boot/patches/ 可以获得当前的引导装载程序的补丁。

Untar the sources, apply the patch. run "make gta01bv3_config" (or gta01bv2_config, or whatever hardware revision you have), run "make". You will get a resulting "u-boot.bin" image, which you can directly flash (either using existing bootloader or sjf2410-linux) into NAND.

引导装载程序二进制文件

最新的引导装载程序二进制文件可以从 http://buildhost.openmoko.org/tmp/gta01/deploy/images/ 网站找到。它应该写到 NAND flash 0x00000000 (size 0x30000) 地址处。

引导装载程序开发

QT2410

If you want to do bootloader development on the QT2410, it's easier to work with a bootloader image that can be downloaded via USB into RAM instead of flashing.

To do so, you need to edit the u-boot/include/configs/qt2410.h file, and change the "if 0" in Line 32 into a "if 1", then recompile with "make".

The resulting "u-boot.bin" is _NOT SUITABLE_ for NAND flash, but only for direct execution from within ram, e.g. by using the s3c2410_boot_usb program.

GTA01

Doing bootloader development on the GTA01 is a bit more tricky. first, we don't have any NOR flash. Second, there is no other way to boot _but_ from NAND. Therefore, we also don't have a USB downloader like the QT2410.

The main problem is: The S3C2410 Steppingstone unconditionally copies the first 4k of flash into its internal SRAM. That SRAM segment stays unconditionally mapped at physical address zero. How do we get around this

使用JTAG从RAM启动

So how can we boot from RAM? We use JTAG / OpenOCD to

  • reset and halt the cpu at PC=0
> reset halt
target halted in ARM state due to debug request, current mode: Supervisor
cpsr: 0x400000d3 pc: 0x00000000
MMU: disabled, D-Cache: disabled, I-Cache: disabled
  • download a small piece of code for low-level SDRAM timing initialization (overwrite 4k SRAM of steppingstone)
> load_binary /space/misc/gta01/u-boot.git/foo.bin 0            
downloaded 332 byte in 0s 21899us
  • assert a break point at address 0x33f80000 (which indicates that the low-level code has finished)
> bp 0x33f80000 4 hw
breakpoint added at address 0x33f80000
  • run the code up to the break point
> resume
Target 0 resumed
> Target 0 halted
target halted in ARM state due to breakpoint, current mode: Supervisor
cpsr: 0x600000d3 pc: 0x33f80000
MMU: disabled, D-Cache: disabled, I-Cache: enabled
  • download the u-boot RAM image to 0x33f80000
> load_binary /space/misc/gta01/u-boot.git/u-boot.bin 0x33f80000
downloaded 135692 byte in 6s 567264us
  • resume processing
> resume
Target 0 resumed

At this point, the display backlight gets bright and we see the following familiar prompt on the serial console:

U-Boot 1.1.6 (Jan 13 2007 - 23:44:23)

DRAM:  128 MB
NAND:  64 MiB
*** Warning - bad CRC or NAND, using default environment

In:    serial
Out:   serial
Err:   serial
Hit any key to stop autoboot:  0 
GTA01Bv2 # 

建立可引导的映像文件

u-boot needs bootable images (such as kernels, but also initrd and others) in form of a so-called uImage. In order to create a uImage from e.g. a vmlinux kernel image, you can proceed as follows:

objcopy -O binary -R .note -R .comment -S vmlinux linux.bin
gzip -9 linux.bin
u-boot/tools/mkimage -A arm -O linux -T kernel -C gzip -a 30008000 -e 30008000 -n "Kernel Image QT2410" -d linux.bin.gz uImage

引导菜单

u-boot boot menu on Neo1973

As of the Phase-0 release, our u-boot version now features an on-screen boot menu.

进入引导菜单

You can access the boot meny by pressing and holding the Neo1973 AUX Button together with the power button while switching the phone on.

使用引导菜单

By pressing the Neo1973 AUX Button you can cycle through the menu items. Use the POWER button to select one item.

给引导菜单增加项目

You can add items to the boot menu by setting environment variables. FIXME.

引导装载程序命令提示行

Accessing the bootloader prompt

The bootloader prompt is available either on the serial console (via Debug Board), or as virtual USB Serial device (USB CDC_ACM). Whether the serial port or usb i used depends on the u-boot environment variables stdin, stdout and stderr.

Whether or not you use usbtty, the first couple of messages will always be displayed on the serial console.

The bootloader is currently configured to waid for three seconds. If a key press on the stdin is received within those three seconds, auto-boot is aborted.

Using usbtty from Linux

Just by connecting the phone in u-boot mode to your Linux pc should make it detect a CDC ACM device, and you should get a new tty device called /dev/ttySAC0. Use your favourite terminal emulator (minicom, cu, zc, ...) to access it like any other serial port.

First, you should try to check whether the USB device shows up in 'lsusb' while you're running in u-boot mode:

# lsusb -d 1457:5119
Bus 005 Device 079: ID 1457:5119  
# lsusb -v -d 1457:5119
Bus 005 Device 079: ID 1457:5119  
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               1.10
  bDeviceClass            2 Communications
  bDeviceSubClass         0 
  bDeviceProtocol         0 
  bMaxPacketSize0        16
  idVendor           0x1457 
  idProduct          0x5119 
  bcdDevice            0.00
  iManufacturer           1 OpenMoko, Inc
  iProduct                2 Neo1973 Bootloader U-Boot 1.2.0-g6c7cac8c-dirty-moko3
  iSerial                 3 0000000
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           85
    bNumInterfaces          3
    bConfigurationValue     1
    iConfiguration          4 TTY via USB
    bmAttributes         0xc0
      Self Powered
    MaxPower                0mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           1
      bInterfaceClass         2 Communications
      bInterfaceSubClass      2 Abstract (modem)
      bInterfaceProtocol      1 AT-commands (v.25ter)
      iInterface              6 Control Interface
      CDC Header:
        bcdCDC               0.6e
      CDC Call Management:
        bmCapabilities       0x00
        bDataInterface          1
      CDC ACM:
        bmCapabilities       0x00
      CDC Union:
        bMasterInterface        0
        bSlaveInterface         1 
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0010  1x 16 bytes
        bInterval             255
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        1
      bAlternateSetting       0
      bNumEndpoints           2
      bInterfaceClass        10 CDC Data
      bInterfaceSubClass      0 Unused
      bInterfaceProtocol      0 
      iInterface              5 Bulk Data Interface
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x02  EP 2 OUT
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0010  1x 16 bytes
        bInterval             255
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x83  EP 3 IN
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0010  1x 16 bytes
        bInterval             255
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        2
      bAlternateSetting       0
      bNumEndpoints           0
      bInterfaceClass       254 Application Specific Interface
      bInterfaceSubClass      1 Device Firmware Update
      bInterfaceProtocol      1 
      iInterface              7 USB Device Firmware Upgrade
Device Status:     0x0001
  Self Powered

Next, you can access it using your favourite terminal program.

Then, if the environment is not set correctly, you will need to use the current console (e.g. serial console) to set

GTA01Bv2 # setenv stderr usbtty
GTA01Bv2 # setenv stdout usbtty
GTA01Bv2 # setenv stdin usbtty

Typical u-boot prompt

U-Boot 1.2.0-moko1 (Feb 16 2007 - 00:36:13)

DRAM:  128 MB
NAND:  64 MiB
Found Environment offset in OOB..
Video: 640x480x8 31kHz 59Hz
USB:   S3C2410 USB Deviced
In:    serial
Out:   serial
Err:   serial
Hit any key to stop autoboot:  0 
GTA01Bv3 #

Commands on the bootloader prompt

自动引导

Auto-boot executes the command[s] specified in the bootcmd environment variable. The default configuration is:

GTA01Bv3 # printenv
bootcmd=setenv bootargs ${bootargs_base} ${mtdparts}; nand read.e 0x32000000 kernel; bootm 0x32000000

This basically tells us that it will load the content of the NAND partition kernel to memory address 0x32000000 and then try to boot it.

环境变量

u-boot is configured to manage a non-volatile environment that is stored in NAND flash. You can use the commands to read/alter/store the environment in the following example:

GTA01Bv2 # printenv
baudrate=115200
bootargs=rootfstype=jffs2 root=/dev/mtdblock4 console=ttySAC0,115200 console=tty0 loglevel=8 dyntick=enable lpj=252416
usbtty=cdc_acm
bootdelay=10
stdout=serial
stderr=serial
stdin=serial
mtdparts=mtdparts=neo1973-nand:0x00030000(u-boot),0x0000c000(u-boot_env),0x00200000(kernel),0x00130000(splash),0x03c94000(rootfs)
mtdids=nand0=neo1973-nand
bootargs_base=rootfstype=jffs2 root=/dev/mtdblock4 console=ttySAC0,115200 console=tty0 loglevel=8 dyntick=enable lpj=252416
bootcmd=setenv bootargs ${bootargs_base} ${mtdparts}; nand read.e 0x32000000 kernel; bootm 0x32000000
pcf50606_int1=0x40
filesize=160C000
partition=nand0,0
mtddevnum=0
mtddevname=u-boot

Environment size: 670/16380 bytes
GTA01Bv3 # setenv bootdelay 10
GTA01Bv3 # printenv bootdelay
bootdelay=10
GTA01Bv3 # saveenv
Saving Environment to NAND...
Erasing Nand...Writing to Nand... done
GTA01Bv3 # 

Note: When setting multiple commands, e.g. for bootcmd, you need to escape the ';', for instance

GTA01Bv3 # setenv bootcmd mmcinit\; ext2load mmc 0 0x32000000 uImage\; bootm 0x32000000

MMC/SD卡

in order to initialize a MMC/SD card, you have to use the ``mmcinit command.

GTA01Bv3 # mmcinit
trying to detect SD Card...
MMC found. Card desciption is:
Manufacturer ID = 58d564
HW/FW Revision = 3 8
Product Name = 21DN!@X�
Serial Number = 445303
Month = 5
Year = 2000
READ_BL_LEN=15, C_SIZE_MULT=7, C_SIZE=3197
size = 4208984064
GTA01Bv3 #

afterwards, you can read ext2 filesystems like:

GTA01Bv3 # ext2ls mmc 0
<DIR>       1024 .
<DIR>       1024 ..
<DIR>      12288 lost+found
         1544788 uImage

NAND

GTA01Bv3 # help nand
nand info                  - show available NAND devices
nand device [dev]     - show or set current device
nand read[.jffs2]     - addr off size
nand write[.jffs2]    - addr off size - read/write `size' bytes starting
    at offset `off' to/from memory address `addr'
nand erase [clean] [off size] - erase `size' bytes from
    offset `off' (entire device if not specified)
nand bad - show bad blocks
nand dump[.oob] off - dump page
nand scrub - really clean NAND erasing bad blocks (UNSAFE)
nand markbad off - mark bad block at offset (UNSAFE)
nand biterr off - make a bit error at offset (UNSAFE)
从 NAND 加载内核
GTA01Bv3 # nand read 0x32000000 kernel

NAND read: device 0 offset 212992, size 2097152 ...  2097152 bytes read: OK
GTA01Bv3 # bootm 0x32000000
## Booting image at 32000000 ...
   Image Name:   OpenMoko Kernel Image Neo1973
   Created:      2007-02-15  23:54:18 UTC
   Image Type:   ARM Linux Kernel Image (gzip compressed)
   Data Size:    1546258 Bytes =  1.5 MB
   Load Address: 30008000
   Entry Point:  30008000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
Starting kernel ...
向 NAND 写新的引导装载程序

The following set of commands loads the file u-boot.bin from ext2/mmc and flashes it into the bootloader flash partition:

GTA01Bv3 # ext2load mmc 0 0x32000000 u-boot.bin
GTA01Bv3 # nand erase u-boot
GTA01Bv3 # nand write 0x32000000 u-boot ${filesize}
Writing kernel to NAND

The following set of commands loads the file uImage from ext2/mmc and flashes it into the kernel flash partition:

GTA01Bv3 # ext2load mmc 0 0x32000000 uImage
GTA01Bv3 # nand erase kernel
GTA01Bv3 # nand write.e 0x32000000 kernel ${filesize}
Writing rootfs to NAND

The following set of commands loads the file rootfs.jffs2 from ext2/mmc and flashes it into the rootfs flash partition:

GTA01Bv3 # ext2load mmc 0 0x32000000 rootfs.jffs2
GTA01Bv3 # nand erase rootfs
GTA01Bv3 # nand write.e 0x32000000 rootfs ${filesize}

Please note that this will only work with root file system sizes that are smaller than the amount of memory above 0x32000000, which in the case of 64MB SDRAM is something like 32MB.

Neo1973 related commands

Our version of u-boot supports a couple of Neo1973 specific commands:

GTA01Bv2 # help neo1973
neo1973 neo1973 info - display phone informantion
neo1973 power-off - switch off the phone
neo1973 charger status - display charger status
neo1973 charger autofast - enable automatic fast (500mA) charging
neo1973 charger !autofast - disable automatic fast (500mA) charging
neo1973 charger fast - enable fast (500mA) charging
neo1973 charger off - disable charging
neo1973 backlight (on|off) - switch backlight on or off
neo1973 vibrator (on|off) - switch vibrator on or off
Power-off

Using

neo1973 power-off

you can switch the device off from the bootloader prompt.

Battery charger related

For a detailed description of the charger basics, see Neo1973 Battery Charger.

Inquiring the charger state

You can get the current charger status by issuing

neo1973 charger status

The following modes are possible:

  • idle - no charging
  • trickle - FIXME
  • pre - Slow (100mA) charging, works in hardware.
  • fast_cccv - Fast (500mA) charging, using Constant-Current followed by Constant Voltage (Li-Ion)
Disabling battery charging

You can disable battery charging (until the next reboot) by issuing

neo1973 charger off
Forcing fast charge

Using

neo1973 charger fast

you can force the PMU to try to do a fast (500mA) charge of the battery. It will abort if the battery is in over temperature or some other error condition occurs.

Enabling / Disabling automatic fast charge

Autofast is a feature of the PCF50606 PMU. It means that the fast_cccv mode will be automatically selected if a charger with suitable voltage is plugged in, and the battery not in over temperature condition.

WARNING: This is potentially dangerous. Only enable autofast if you ARE SURE that you can draw 500mA from the USB connector. This is the case with a wall outlet charger, or if you are attached to a self-powered hub or a desktop PC root hub. Bus powered hubs and some laptops only provide 100mA on their USB ports and can thus not support fast charging


You can enable or disable autofast by

neo1973 charger autofast

and

neo1973 charger !autofast

respectively.

Backlight

You can switch the backlight on and off by using

neo1973 backlight on

and

neo1973 backlight off

respectively.

Vibrator

You can switch the vibrator on and off by using

neo1973 vibrator on

and

neo1973 vibrator off

respectively.

S3C2410 specific commands

GTA01Bv2 # help s3c2410
s3c2410 speed get - display current PLL speed config
s3c2410 speed list - display supporte PLL speed configs
s3c2410 speed set - set PLL speed
GTA01Bv2 # s3c2410 speed list
50 MHz
101 MHz
202 MHz
266 MHz
GTA01Bv2 # s3c2410 speed get
FCLK = 202 MHz, HCLK = 101 MHz, PCLK = 50 MHz
GTA01Bv2 # s3c2410 speed set 101
GTA01Bv2 # s3c2410 speed get
FCLK = 101 MHz, HCLK = 50 MHz, PCLK = 50 MHz
266MHz时钟

You can re-configure the S3C2410 PLL to generate a 266 MHz core cpu clock (rather than the 200MHz default) by using

GTA01Bv2 # s3c2410 speed set 266 

and

GTA01Bv2 # s3c2410 speed set 202

respectively.

WARNING: The current hardware (as of GTA01Bv3) only runs stable at 266MHz if you do not attach aynthing (esp. the FPC / Debug Board to the Debug Port


QT2410上的TFTP

The QT2410 cs8900a Ethernet can be used to download images via network.

First, you have to make sure that ipaddr, serverip, ethaddr' and netmaskk are set correctly in the environment:

QT2410 # printenv
ethaddr=00:01:02:03:04:05
netmask=255.255.255.0
ipaddr=192.168.100.100
serverip=192.168.100.1


TFTP kernel download
QT2410 # tftpboot 0x32000000
*** Warning: no boot file name; using 'C0A86464.img'
TFTP from server 192.168.100.1; our IP address is 192.168.100.100
Filename 'C0A86464.img'.
Load address: 0x32000000
Loading: #################################################################
         #################################################################
         #################################################################
         #################################################################
         ##########################################
done
Bytes transferred = 1544788 (179254 hex)

you can then commence booting via

QT2410# bootm 0x32000000

设备固件升级

Our version of u-boot also implements USB DFU.

To find out whether your version of u-boot supports this, use the output of

$ lsusb -v -d 1457:5119

while the phone is in u-boot mode.

If it supports DFU, you should see the following snippet towards the end of the output:

    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        2
      bAlternateSetting       0
      bNumEndpoints           0
      bInterfaceClass       254 Application Specific Interface
      bInterfaceSubClass      1 Device Firmware Update
      bInterfaceProtocol      1 
      iInterface              0 

关于如何进行固件升级的信息,请看dfu-util

Personal tools
File:Uboot-s3c2410fb.jpg
Neo1973控制台上的u-boot
Neo1973上的u-boot引导菜单

概述

GTA01使用了u-boot引导装载程序。

关于u-boot的更多信息可以在下列地方找到

但是,未经修改的u-boot不支持GTA01所需要的许多特性,比如

  • 利用S3C2410 Steppingstone从NAND闪存启动
  • 从SD/Transflash读取内核/initrd
  • S3C2410 NAND闪存
  • 通过S3C2410 USB Device控制器下载程序
  • S3C2410 Framebuffer启动logo/状态显示

Harald Welte正在为这些解决问题而工作,并且实际上它们中的大多数已经得到了实现。

引导装载程序源代码

http://svn.openmoko.org/trunk/src/target/u-boot/patches/ 可以获得当前的引导装载程序的补丁。

Untar the sources, apply the patch. run "make gta01bv3_config" (or gta01bv2_config, or whatever hardware revision you have), run "make". You will get a resulting "u-boot.bin" image, which you can directly flash (either using existing bootloader or sjf2410-linux) into NAND.

引导装载程序二进制文件

最新的引导装载程序二进制文件可以从 http://buildhost.openmoko.org/tmp/gta01/deploy/images/ 网站找到。它应该写到 NAND flash 0x00000000 (size 0x30000) 地址处。

引导装载程序开发

QT2410

If you want to do bootloader development on the QT2410, it's easier to work with a bootloader image that can be downloaded via USB into RAM instead of flashing.

To do so, you need to edit the u-boot/include/configs/qt2410.h file, and change the "if 0" in Line 32 into a "if 1", then recompile with "make".

The resulting "u-boot.bin" is _NOT SUITABLE_ for NAND flash, but only for direct execution from within ram, e.g. by using the s3c2410_boot_usb program.

GTA01

Doing bootloader development on the GTA01 is a bit more tricky. first, we don't have any NOR flash. Second, there is no other way to boot _but_ from NAND. Therefore, we also don't have a USB downloader like the QT2410.

The main problem is: The S3C2410 Steppingstone unconditionally copies the first 4k of flash into its internal SRAM. That SRAM segment stays unconditionally mapped at physical address zero. How do we get around this

使用JTAG从RAM启动

So how can we boot from RAM? We use JTAG / OpenOCD to

  • reset and halt the cpu at PC=0
> reset halt
target halted in ARM state due to debug request, current mode: Supervisor
cpsr: 0x400000d3 pc: 0x00000000
MMU: disabled, D-Cache: disabled, I-Cache: disabled
  • download a small piece of code for low-level SDRAM timing initialization (overwrite 4k SRAM of steppingstone)
> load_binary /space/misc/gta01/u-boot.git/foo.bin 0            
downloaded 332 byte in 0s 21899us
  • assert a break point at address 0x33f80000 (which indicates that the low-level code has finished)
> bp 0x33f80000 4 hw
breakpoint added at address 0x33f80000
  • run the code up to the break point
> resume
Target 0 resumed
> Target 0 halted
target halted in ARM state due to breakpoint, current mode: Supervisor
cpsr: 0x600000d3 pc: 0x33f80000
MMU: disabled, D-Cache: disabled, I-Cache: enabled
  • download the u-boot RAM image to 0x33f80000
> load_binary /space/misc/gta01/u-boot.git/u-boot.bin 0x33f80000
downloaded 135692 byte in 6s 567264us
  • resume processing
> resume
Target 0 resumed

At this point, the display backlight gets bright and we see the following familiar prompt on the serial console:

U-Boot 1.1.6 (Jan 13 2007 - 23:44:23)

DRAM:  128 MB
NAND:  64 MiB
*** Warning - bad CRC or NAND, using default environment

In:    serial
Out:   serial
Err:   serial
Hit any key to stop autoboot:  0 
GTA01Bv2 # 

建立可引导的映像文件

u-boot needs bootable images (such as kernels, but also initrd and others) in form of a so-called uImage. In order to create a uImage from e.g. a vmlinux kernel image, you can proceed as follows:

objcopy -O binary -R .note -R .comment -S vmlinux linux.bin
gzip -9 linux.bin
u-boot/tools/mkimage -A arm -O linux -T kernel -C gzip -a 30008000 -e 30008000 -n "Kernel Image QT2410" -d linux.bin.gz uImage

引导菜单

u-boot boot menu on Neo1973

As of the Phase-0 release, our u-boot version now features an on-screen boot menu.

进入引导菜单

You can access the boot meny by pressing and holding the Neo1973 AUX Button together with the power button while switching the phone on.

使用引导菜单

By pressing the Neo1973 AUX Button you can cycle through the menu items. Use the POWER button to select one item.

给引导菜单增加项目

You can add items to the boot menu by setting environment variables. FIXME.

引导装载程序命令提示行

Accessing the bootloader prompt

The bootloader prompt is available either on the serial console (via Debug Board), or as virtual USB Serial device (USB CDC_ACM). Whether the serial port or usb i used depends on the u-boot environment variables stdin, stdout and stderr.

Whether or not you use usbtty, the first couple of messages will always be displayed on the serial console.

The bootloader is currently configured to waid for three seconds. If a key press on the stdin is received within those three seconds, auto-boot is aborted.

Using usbtty from Linux

Just by connecting the phone in u-boot mode to your Linux pc should make it detect a CDC ACM device, and you should get a new tty device called /dev/ttySAC0. Use your favourite terminal emulator (minicom, cu, zc, ...) to access it like any other serial port.

First, you should try to check whether the USB device shows up in 'lsusb' while you're running in u-boot mode:

# lsusb -d 1457:5119
Bus 005 Device 079: ID 1457:5119  
# lsusb -v -d 1457:5119
Bus 005 Device 079: ID 1457:5119  
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               1.10
  bDeviceClass            2 Communications
  bDeviceSubClass         0 
  bDeviceProtocol         0 
  bMaxPacketSize0        16
  idVendor           0x1457 
  idProduct          0x5119 
  bcdDevice            0.00
  iManufacturer           1 OpenMoko, Inc
  iProduct                2 Neo1973 Bootloader U-Boot 1.2.0-g6c7cac8c-dirty-moko3
  iSerial                 3 0000000
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           85
    bNumInterfaces          3
    bConfigurationValue     1
    iConfiguration          4 TTY via USB
    bmAttributes         0xc0
      Self Powered
    MaxPower                0mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           1
      bInterfaceClass         2 Communications
      bInterfaceSubClass      2 Abstract (modem)
      bInterfaceProtocol      1 AT-commands (v.25ter)
      iInterface              6 Control Interface
      CDC Header:
        bcdCDC               0.6e
      CDC Call Management:
        bmCapabilities       0x00
        bDataInterface          1
      CDC ACM:
        bmCapabilities       0x00
      CDC Union:
        bMasterInterface        0
        bSlaveInterface         1 
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0010  1x 16 bytes
        bInterval             255
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        1
      bAlternateSetting       0
      bNumEndpoints           2
      bInterfaceClass        10 CDC Data
      bInterfaceSubClass      0 Unused
      bInterfaceProtocol      0 
      iInterface              5 Bulk Data Interface
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x02  EP 2 OUT
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0010  1x 16 bytes
        bInterval             255
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x83  EP 3 IN
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0010  1x 16 bytes
        bInterval             255
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        2
      bAlternateSetting       0
      bNumEndpoints           0
      bInterfaceClass       254 Application Specific Interface
      bInterfaceSubClass      1 Device Firmware Update
      bInterfaceProtocol      1 
      iInterface              7 USB Device Firmware Upgrade
Device Status:     0x0001
  Self Powered

Next, you can access it using your favourite terminal program.

Then, if the environment is not set correctly, you will need to use the current console (e.g. serial console) to set

GTA01Bv2 # setenv stderr usbtty
GTA01Bv2 # setenv stdout usbtty
GTA01Bv2 # setenv stdin usbtty

Typical u-boot prompt

U-Boot 1.2.0-moko1 (Feb 16 2007 - 00:36:13)

DRAM:  128 MB
NAND:  64 MiB
Found Environment offset in OOB..
Video: 640x480x8 31kHz 59Hz
USB:   S3C2410 USB Deviced
In:    serial
Out:   serial
Err:   serial
Hit any key to stop autoboot:  0 
GTA01Bv3 #

Commands on the bootloader prompt

自动引导

Auto-boot executes the command[s] specified in the bootcmd environment variable. The default configuration is:

GTA01Bv3 # printenv
bootcmd=setenv bootargs ${bootargs_base} ${mtdparts}; nand read.e 0x32000000 kernel; bootm 0x32000000

This basically tells us that it will load the content of the NAND partition kernel to memory address 0x32000000 and then try to boot it.

环境变量

u-boot is configured to manage a non-volatile environment that is stored in NAND flash. You can use the commands to read/alter/store the environment in the following example:

GTA01Bv2 # printenv
baudrate=115200
bootargs=rootfstype=jffs2 root=/dev/mtdblock4 console=ttySAC0,115200 console=tty0 loglevel=8 dyntick=enable lpj=252416
usbtty=cdc_acm
bootdelay=10
stdout=serial
stderr=serial
stdin=serial
mtdparts=mtdparts=neo1973-nand:0x00030000(u-boot),0x0000c000(u-boot_env),0x00200000(kernel),0x00130000(splash),0x03c94000(rootfs)
mtdids=nand0=neo1973-nand
bootargs_base=rootfstype=jffs2 root=/dev/mtdblock4 console=ttySAC0,115200 console=tty0 loglevel=8 dyntick=enable lpj=252416
bootcmd=setenv bootargs ${bootargs_base} ${mtdparts}; nand read.e 0x32000000 kernel; bootm 0x32000000
pcf50606_int1=0x40
filesize=160C000
partition=nand0,0
mtddevnum=0
mtddevname=u-boot

Environment size: 670/16380 bytes
GTA01Bv3 # setenv bootdelay 10
GTA01Bv3 # printenv bootdelay
bootdelay=10
GTA01Bv3 # saveenv
Saving Environment to NAND...
Erasing Nand...Writing to Nand... done
GTA01Bv3 # 

Note: When setting multiple commands, e.g. for bootcmd, you need to escape the ';', for instance

GTA01Bv3 # setenv bootcmd mmcinit\; ext2load mmc 0 0x32000000 uImage\; bootm 0x32000000

MMC/SD卡

in order to initialize a MMC/SD card, you have to use the ``mmcinit command.

GTA01Bv3 # mmcinit
trying to detect SD Card...
MMC found. Card desciption is:
Manufacturer ID = 58d564
HW/FW Revision = 3 8
Product Name = 21DN!@X�
Serial Number = 445303
Month = 5
Year = 2000
READ_BL_LEN=15, C_SIZE_MULT=7, C_SIZE=3197
size = 4208984064
GTA01Bv3 #

afterwards, you can read ext2 filesystems like:

GTA01Bv3 # ext2ls mmc 0
<DIR>       1024 .
<DIR>       1024 ..
<DIR>      12288 lost+found
         1544788 uImage

NAND

GTA01Bv3 # help nand
nand info                  - show available NAND devices
nand device [dev]     - show or set current device
nand read[.jffs2]     - addr off size
nand write[.jffs2]    - addr off size - read/write `size' bytes starting
    at offset `off' to/from memory address `addr'
nand erase [clean] [off size] - erase `size' bytes from
    offset `off' (entire device if not specified)
nand bad - show bad blocks
nand dump[.oob] off - dump page
nand scrub - really clean NAND erasing bad blocks (UNSAFE)
nand markbad off - mark bad block at offset (UNSAFE)
nand biterr off - make a bit error at offset (UNSAFE)
从 NAND 加载内核
GTA01Bv3 # nand read 0x32000000 kernel

NAND read: device 0 offset 212992, size 2097152 ...  2097152 bytes read: OK
GTA01Bv3 # bootm 0x32000000
## Booting image at 32000000 ...
   Image Name:   OpenMoko Kernel Image Neo1973
   Created:      2007-02-15  23:54:18 UTC
   Image Type:   ARM Linux Kernel Image (gzip compressed)
   Data Size:    1546258 Bytes =  1.5 MB
   Load Address: 30008000
   Entry Point:  30008000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
Starting kernel ...
向 NAND 写新的引导装载程序

The following set of commands loads the file u-boot.bin from ext2/mmc and flashes it into the bootloader flash partition:

GTA01Bv3 # ext2load mmc 0 0x32000000 u-boot.bin
GTA01Bv3 # nand erase u-boot
GTA01Bv3 # nand write 0x32000000 u-boot ${filesize}
Writing kernel to NAND

The following set of commands loads the file uImage from ext2/mmc and flashes it into the kernel flash partition:

GTA01Bv3 # ext2load mmc 0 0x32000000 uImage
GTA01Bv3 # nand erase kernel
GTA01Bv3 # nand write.e 0x32000000 kernel ${filesize}
Writing rootfs to NAND

The following set of commands loads the file rootfs.jffs2 from ext2/mmc and flashes it into the rootfs flash partition:

GTA01Bv3 # ext2load mmc 0 0x32000000 rootfs.jffs2
GTA01Bv3 # nand erase rootfs
GTA01Bv3 # nand write.e 0x32000000 rootfs ${filesize}

Please note that this will only work with root file system sizes that are smaller than the amount of memory above 0x32000000, which in the case of 64MB SDRAM is something like 32MB.

Neo1973 related commands

Our version of u-boot supports a couple of Neo1973 specific commands:

GTA01Bv2 # help neo1973
neo1973 neo1973 info - display phone informantion
neo1973 power-off - switch off the phone
neo1973 charger status - display charger status
neo1973 charger autofast - enable automatic fast (500mA) charging
neo1973 charger !autofast - disable automatic fast (500mA) charging
neo1973 charger fast - enable fast (500mA) charging
neo1973 charger off - disable charging
neo1973 backlight (on|off) - switch backlight on or off
neo1973 vibrator (on|off) - switch vibrator on or off
Power-off

Using

neo1973 power-off

you can switch the device off from the bootloader prompt.

Battery charger related

For a detailed description of the charger basics, see Neo1973 Battery Charger.

Inquiring the charger state

You can get the current charger status by issuing

neo1973 charger status

The following modes are possible:

  • idle - no charging
  • trickle - FIXME
  • pre - Slow (100mA) charging, works in hardware.
  • fast_cccv - Fast (500mA) charging, using Constant-Current followed by Constant Voltage (Li-Ion)
Disabling battery charging

You can disable battery charging (until the next reboot) by issuing

neo1973 charger off
Forcing fast charge

Using

neo1973 charger fast

you can force the PMU to try to do a fast (500mA) charge of the battery. It will abort if the battery is in over temperature or some other error condition occurs.

Enabling / Disabling automatic fast charge

Autofast is a feature of the PCF50606 PMU. It means that the fast_cccv mode will be automatically selected if a charger with suitable voltage is plugged in, and the battery not in over temperature condition.

WARNING: This is potentially dangerous. Only enable autofast if you ARE SURE that you can draw 500mA from the USB connector. This is the case with a wall outlet charger, or if you are attached to a self-powered hub or a desktop PC root hub. Bus powered hubs and some laptops only provide 100mA on their USB ports and can thus not support fast charging


You can enable or disable autofast by

neo1973 charger autofast

and

neo1973 charger !autofast

respectively.

Backlight

You can switch the backlight on and off by using

neo1973 backlight on

and

neo1973 backlight off

respectively.

Vibrator

You can switch the vibrator on and off by using

neo1973 vibrator on

and

neo1973 vibrator off

respectively.

S3C2410 specific commands

GTA01Bv2 # help s3c2410
s3c2410 speed get - display current PLL speed config
s3c2410 speed list - display supporte PLL speed configs
s3c2410 speed set - set PLL speed
GTA01Bv2 # s3c2410 speed list
50 MHz
101 MHz
202 MHz
266 MHz
GTA01Bv2 # s3c2410 speed get
FCLK = 202 MHz, HCLK = 101 MHz, PCLK = 50 MHz
GTA01Bv2 # s3c2410 speed set 101
GTA01Bv2 # s3c2410 speed get
FCLK = 101 MHz, HCLK = 50 MHz, PCLK = 50 MHz
266MHz时钟

You can re-configure the S3C2410 PLL to generate a 266 MHz core cpu clock (rather than the 200MHz default) by using

GTA01Bv2 # s3c2410 speed set 266 

and

GTA01Bv2 # s3c2410 speed set 202

respectively.

WARNING: The current hardware (as of GTA01Bv3) only runs stable at 266MHz if you do not attach aynthing (esp. the FPC / Debug Board to the Debug Port


QT2410上的TFTP

The QT2410 cs8900a Ethernet can be used to download images via network.

First, you have to make sure that ipaddr, serverip, ethaddr' and netmaskk are set correctly in the environment:

QT2410 # printenv
ethaddr=00:01:02:03:04:05
netmask=255.255.255.0
ipaddr=192.168.100.100
serverip=192.168.100.1


TFTP kernel download
QT2410 # tftpboot 0x32000000
*** Warning: no boot file name; using 'C0A86464.img'
TFTP from server 192.168.100.1; our IP address is 192.168.100.100
Filename 'C0A86464.img'.
Load address: 0x32000000
Loading: #################################################################
         #################################################################
         #################################################################
         #################################################################
         ##########################################
done
Bytes transferred = 1544788 (179254 hex)

you can then commence booting via

QT2410# bootm 0x32000000

设备固件升级

Our version of u-boot also implements USB DFU.

To find out whether your version of u-boot supports this, use the output of

$ lsusb -v -d 1457:5119

while the phone is in u-boot mode.

If it supports DFU, you should see the following snippet towards the end of the output:

    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        2
      bAlternateSetting       0
      bNumEndpoints           0
      bInterfaceClass       254 Application Specific Interface
      bInterfaceSubClass      1 Device Firmware Update
      bInterfaceProtocol      1 
      iInterface              0 

关于如何进行固件升级的信息,请看dfu-util