Qi/ru - Revision history

GreyCardinal: /* Requirements */

2009-07-23T13:03:52Z

‎Requirements

2009-07-23T13:03:18Z

‎Installation

2009-07-23T13:02:53Z

‎Boot Menu

2009-07-23T13:02:32Z

‎/boot-Partition

2009-07-23T13:02:14Z

‎Enabling console messages

2009-07-23T13:01:45Z

‎General troubleshooting

2009-07-23T13:01:12Z

‎Choosing a Kernel

2009-07-23T13:00:51Z

‎Booting

2009-07-23T13:00:18Z

‎Boot Order

2009-07-23T12:59:59Z

‎Defaults

@@ Line 11: / Line 11: @@
 ==Информация о Qi==
-===Requirements===
+===Требования===
 There is a [[Neo1973|GTA01]] build of Qi, but using it without a debug board is not recommended because Qi itself does not support DFU, so updating or going back to U-Boot is a difficult process.

@@ Line 44: / Line 44: @@
 Используйте по вашему усмотрению:
-===Installation===
+===Установка===
 The installation should be flashing like (do it in DFU mode of NOR u-boot):
   # dfu-util -a u-boot -R -D qi-s3<version>.udfu

@@ Line 145: / Line 145: @@
 debugging parameters are added to the kernel command line and a lot of information is output to the screen.
-===Boot Menu===
+===Boot меню===
 Qi's concept is to leave everything possible to Linux, that includes even the video init. Therefore Qi does NOT provide a boot menu. This should rather be implemented by a minimal Kernel, initramfs and menu system. It may be more comfortable for some users and may get them to switch from uboot to Qi. This does not exist yet (it's already implemented for some Angstrom-supported devices and for Zaurus, so porting should be relatively easy).
 ===Source code===

@@ Line 176: / Line 176: @@
 and you'll see the messages on boot.  If it's NAND right now you need to edit the default commandline in Qi for gta02.
-===/boot-Partition===
+===/boot-разделы===
 If you have a separate partition for /boot, so that your kernel and rootfs are not in fact on the same partition, you will need to append a root= entry on the kernel commandline to override the default action of trying to use the partition where the kernel came from as the rootfs.

@@ Line 163: / Line 163: @@
 If nothing else is happening or there is a panic, enable debugging messages as described below.
-===Enabling console messages===
+===Включить сообщения в консоли===
 You can just hold in the power button, this automatically appends verbose debugging to the kernel commandline (loglevel=8).

@@ Line 158: / Line 158: @@
 ==Tips, Tricks, Tweaks==
-===General troubleshooting===
+===Основные проблемы===
 Qi does not bring up the LCD backlight.  If the backlight is lit, it means you have succeeded to boot into Linux.

@@ Line 136: / Line 136: @@
 You can force debug messages on the LCM console by holding in the power button before Linux starts.
-===Choosing a Kernel===
+===Выбор ядра===
 If a user presses the AUX button after successful partition mount and
 before start of the kernel pull (that is, while the red LED is on),

@@ Line 131: / Line 131: @@
 * About four RED shines per second: kernel panic.
-===Booting===
+===Загрузка===
 A short press on the power button is enough to make Qi start booting. In a few seconds the backlight will be lit, but the kernel will not spew any console messages unless something is wrong. It may take up to 2 minutes (depends on distribution) until X is started during which there will be no visual feedback. Please be patient.

@@ Line 96: / Line 96: @@
 : loglevel=1 quiet
 The disadvantage of this speedup is that you won't see any lifesign of your phone until it starts the graphical user interface after adding these files, though.
-===Boot Order===
+===Порядок загрузки===
 [[image:Qi-drawings-bootsequence.png|frame|Qi GTA02 Booting order]]
 # SD Partition 1

@@ Line 81: / Line 81: @@
 FAT is not supported because it can't provide a rootfs, and Qi wants the kernel to come from the rootfs.
-===Defaults===
+===По умолчанию===
 If the kernel is found on uSD, Qi assumes the rootfs to be on the same partition as the kernel. In case of boot from NAND, it assumes that rootfs is also on NAND (just as u-boot does). See [[#/boot-Partition|below]] for help with an extra /boot-partition. The default rootdelay is 1 second.