Neo FreeRunner Hardware

From Openmoko

Revision as of 20:17, 19 November 2009 by Glenn (Talk | contribs)

Jump to: navigation, search



The Neo FreeRunner phone is the second hardware platform to take advantage of the Openmoko software stack. You can find specifications of the hardware by reviewing this introduction page and the pages in the category as shown at the bottom of this page.

For basic details please see the Customer-oriented specifications.

Contents

Photos


Features

  • Display- Topply o2.8, 480 x 640 pixels, VGA, 200 NIT minimum, resistance type touch
  • User Interface Navigation- Touch screen on LCD, 2 control “buttons”, 1 Power button, 1 Aux for 911 emergency call
  • Built-in 802.11b/g Radio (Atheros chipset AR6001 Flash version)
  • Built-in Bluetooth 2.0 + EDR (CSR and support PCM audio , BC4 firmware version)
  • Built-in 2D/3D graphics acceleration chip (S-Media 3362)
  • 2 built-in Tri-Axis sensors (ST accelerometer LIS302DL)
  • Built-in GPS Radio – -130 dBm with internal antenna, -157 dBm tracking on chipset specification, TTFF under 40 seconds with -130 dBm signal strength, and tracking (u-Blox)
  • Antenna – Specialized antenna for best in hand hold GPS, GPRS and Wi-Fi/Bluetooth performance are required, -105dBm on receiving, Tx 30dbm+2 on GSM
  • External Antennae – MMCX GPS connector
  • GPRS Radio –GSM/GPRS radio. A Pre-PTCRB certified module will be preferred
  • Linux – Linux kernel 2.6.24 or later Openmoko kernel
  • USB - Client and Host-mode switchable (to be used for software downloading), provide host 5V power
  • Power- Normal mode power will be via 1200 mAh battery with built-in coulomb counter, could charge via specialized charger. Internal Lithium Ion or Lithium Polymer battery will keep device in standby mode. Battery life (Approximation/Ideal Target) Standby time 70h Hrs (GSM) Talk time (Backlight off) Up to 3-4 hrs(GSM)
  • LED- LED indicator under Aux/Power button key

Hardware Specification

Full schematics are available.

Hardware Electrical

  • 400/500 MHz Samsung 2442B Processor/SOC (400 minimum, ARM920T core, ARMv4T)
  • Unbrickable dual Boot code in NAND FLASH and 2MB NOR FLASH
  • 128 MB SDRAM total, 64 MB CPU internal, 64 MB external
  • 256MB NAND Flash MCP package.

Display

  • Topploy VGA, 16 bit color depth
  • resolution: 480 x 640 pixels
  • size: 43mm x 58mm (1.7” x 2.27”)
  • diagonal: 72.2mm (2.84”)
  • Transmissive display: good readability in high ambient light is essential
  • White LED backlight. Required brightness is 200 NIT minimum.
  • Resistance type touch panel.

WiFi 802.11 b/g transceiver

  • Must have GPL support source or GPL compatible policy
  • TX power at 11 Mbps: 13 dBm minimum
  • RX sensitivity at 11 Mbps: -89 dBm desired, -83 dBm minimum
  • AP mode desirable, not required
  • WEP and WPA supported
  • Atheros preferred because of its GPL policy

Serial interfaces (UART)

  • Three serial interfaces are required
  • Console
  • A-GPS or GPS
  • GSM/GPRS

Accelerometer

  • 2x accelerometer required
  • Could support interrupt while suspend or power save mode
  • 3 axis sensing

A-GPS

  • GPS chipset receiver and antenna
  • Sensitivity at Antenna port: -157 dBm tracking on chipset specification
  • LNA and SAW filter for maximum interference protection
  • Cold start time to first fix: 40 sec typical at -130 dBm, 60 sec max
  • Must support GPL for Assist-GPS function with open API
  • Industry quality GPS
  • Could fit in GTA01 GPS area on the PCB

GPS Antenna Performance

  • Antenna is passive and internal; 15 mm x 15 mm ceramic patch is nominal design
  • Antenna LNA and SAW filter are required to meet GPS performance
  • 15 mm square ground plane (minimum 1 mm ground border around patch) (TBA)
  • There will be one external GPS antenna connector (MMCX)
  • C/N ratio should higher than 35 on production testing

Buttons

  • Touch screen over LCD is primary data entry mechanism
  • Two “hard” buttons: Power button (on side of Neo1973) is a mechanical switch actuated by a plastic pushbutton in a hole in the housing. Aux (911) button on the top of the device, both of these buttons, when pushed by the operator, are binary inputs (on/off or pressed/not pressed) to the software. The effect of each button is determined by the application software in the device
  • Buttons may need to be backlit
  • 50000 cycles on hardware specification

Sound outputs

  • Speaker in box (need good volume and acoustic behavior in noisy environments)
  • Audio is monophonic
  • Max volume: 100 dB at 5 cm to assure good performance in environment.
  • Support earphone with mic by jack

Power Design Requirements

  • Software-based power management unit preferred
  • NXP PCF series preferred
  • Need support charge from USB function
  • Need support powered by USB function
  • Power switch: Neo1973 will have a power switch, for power on/off and suspend
  • Power/Aux switch must be backlit
  • Switch controls whether device is running or suspended by presses of the switch
  • Switch does not shut off the power; it only suspends/resumes the device
  • Internal Li-Ion or Li-Polymer battery is included. This battery supplies standby power to the device eliminates the rebooting of the device when local power is again reapplied. Battery is 1200 ma-hr.
  • Battery life (Approximation) Ideal/Target Standby time 150-200 Hrs (GSM) Talk time (Backlight off) Up to 4 hrs(GSM)
  • Estimated current draw for the entire device when in suspend mode (and ALL peripherals are turned off or set for deep sleep) is <5 mA at 3.6 volts (Li-Ion terminal voltage).
  • GSM module deep sleep(alive and keep contact with base station) stage should take less than 8mA
  • Battery will reach half capacity (~600 mAh) with 500 charge-discharge cycles. This will occur in less than 2 years of daily service.
  • When powered continuously, Neo1973 must suspend (to low power mode) based either on observed low battery voltage condition or a configurable time delay.
  • Neo1973 must monitor battery status while suspended and resume automatically if the charger is inserted.
  • Primary power connection: 1200mAh battery
  • USB charger have ID pin 47.5k pull down for Openmoko identification
  • Indicators: an LED indicator visible from the side of the unit will illuminate when charging or have missing incoming call

GSM/GPRS

  • 850/1800/1900 and 900/1800/1900 MHz bands must be supported
  • Design should allow for multi-band version (850/900 MHz)
  • Module based GPRS transceiver could meet PTCRB and appropriate FCC certifications. It preferred that the module be pre-certified with PTCRB or OTA test
  • FCC/CE certification required for GSM/GPRS part

GSM-GPRS Antenna Performance

  • -105 dBm receiving on each channel (GSM/PCS)
  • 30+2 dBm transmission on GSM channel

SD card reader

  • One micro-SD card reader, compatible with SD and SDHC.

A small speed test can be found on the StorageSpeed page.

Wi-Fi Modules

  • Must support GPL driver
  • Atheros AR6k preferred
  • Flash version required

Wi-Fi Antenna Performance

  • The Wi-Fi antenna with TX 13 to 15 dBm
  • RX -89 to -83 dBm @802.11b 11Mbps or an equivalent performance antenna

Bluetooth

  • CSR BC4 or later solutions

USB

  • Neo FreeRunner GTA02 will have USB, client/host. Using USB 1.1
  • Provides USB host 5v power
  • Could be powered by USB

Microphone

1 microphone is in the device

Firmware Image

  • Using Linux 2.6.24 or later
  • Could support booting from NAND or from NOR
  • Shipping image should come with basic phone function
  • Could do full firmware upgrade by USB cable

PSN

  • Device will have a PSN (product serial number) printed on the product label and machine readable in system NAND memory

IMEI

  • Production phase should have IMEI code written

Package Specification

  • Weight: ~133 grams with battery.
  • 4-in-1 laser pen passed RoHs and safety regulation for laser equipment safety
  • 1x 512MB microSD Card (SanDisk / Transcend TS512MUSD)
  • 1x USB cable Standard A to mini-B connector
  • 1x 1200mAh smart/gauge battery
  • Quick start guide
  • 5v USB power cord w/100-240 switchable power plug
  • Safety card, warranty card
  • Package could pass 1m to 1.5m drop test
  • AC USB charger,100v-240v, Passed UL and all required safety regulations
  • Must pass FCC/CE certification
  • Must pass NCC certification for Taiwan import regulation
  • RoHS Compatible
  • WEEE Report required

Life Cycle Specification

Product Life

The product is designed to last a minimum of 2 years.

Operating Temperature

  • Target operating range is –10°C to +60°C

Storage Temperature

  • -15 deg C to +70 deg C

ESD

The device can withstand a 4.0kV contact discharge and 8.0kV air

Drop test

Should pass 1m direct drop to concrete ground or 1.5m on slide with carpet


GTA02 Hardware Component Selection

Physical Dimensions

  • 120.7 x 62.0 x 18.5 mm (4.752 x 2.441 x 0.728 inch)
  • 110 +/- 5 g (4 ounces) without battery

Main components

Processor

The main Processor (CPU) of the Neo1973 GTA02 is a Samsung S3C2442B B54 (running at 400 MHz)

Power Management

A NXP PCF50633 04 N3 is used for power management.

Flash

NAND Flash

256MB integrated Samsung NAND flash inside the 2442 multi-chip package, attached to the S3C2442 NAND controller

  • Product Homepage: S3C2442
  • Data Sheet: S3C2442 B54 comes with 256 MB NAND MCP package
  • Connected to: S3C2442 NAND controller

NOR Flash

16MBit ST M58WR016KB706E NOR flash for 'unbrickable emergency boot' feature.

SDRAM

128MB SDRAM (64MB inside 2442 MCP, 1x Samsung K4M51323PC) attached to S3C2442 SDRAM controller

GSM/GPRS

The GSM (including GPRS) modem is Texas Instruments Calypso based and supports 2.5G tri-band GPRS/GSM. The two available models support either the 850/1800/1900 MHz bands (suitable for USA), or 900/1800/1900 MHz band (suitable for rest of the world).

CALYPSO ASIC digital baseband

Unfortunately we cannot provide many details on the GSM chipset due to very tight NDAs. However, this is not neccessarily required, since it interfaces using a standard UART serial line with the S3C2442. On that interface, GSM 07.05, GSM 07.10 and other standardized protocols are used.

The NDAd documentation for the calypso, register definition and hardware definition was leaked onto a public forum on the 4th of March by persons or persons unknown. The legality of reading these files may vary according to your local laws, as may generating code from them.


  • Calypso D751992AZHH
  • The firmware within GTA02 should be moko6 or later (internal code name)

TI TWL3025BZGMR analog baseband

TI TRF6151 (GSM/PCS) RF Transceiver

GPRS Class12/CS4

AGPS

u-blox ANTARIS 4 chip

  • Connected to: S3C2442 UART2, /dev/ttySAC1 in userspace
  • Driver: none needed, talks standard NMEA
  • u-blox Antaris 4 Protocol Protocol download page
  • ATR0635 Datasheet: u-blox ATR0635

Accelerometers

Two ST LIS302DL

Graphics/3D Acceleration

Smedia Glamo 3362.

microSD

The GTA02 has one microSD aka Transflash slot. Using the Glamo 3362 MMC/SD controller

LCD Module (LCM)

Toppoly (tpo) 2.8" diagonal (1.7" x 2.27" - 43mm x 58mm) 480x640 TD028TTEC1 module, using a Toshiba JBT6K74 TFT LCD Driver Chipset.

Touch Screen

Bluetooth Module

Delta DFBM-CS320 Class2 Module, using CSR BlueCore4

Bluetooth Audio

This one is wired via PCM bus from the CSR Bluetooth chip to the Wolfson codec.

WiFi Module

Accton (WLAN 802.11b/g SiP-M WM3236AQ(Flash Ver:2.0 Atheros AR6001GZ)

Vibrator

USB Host

The USB Host controller is inside the S3C2442

  • Driver: Stock Linux kernel ohci_hcd
  • USB version 1.1
  • Supply USB 5v in Host mode using usb power switch AAT1275IRN-5.0-T1
  • A net EN_USBHOST is controlled by PMU GPIO "GPO", this one signal when asserted (high)
    • enables generation of 5V for external device using a charge pump
    • enables connection of 15K pulldowns to D+ and D- to allow device insertion and removal detection for host mode
    • DISABLES the path for USB power to charge the battery

It should also be possible to use host mode with externally-provided power. This will allow the FreeRunner to be connected to a USB device and be powered and charging the battery if present at the same time. This method is called the Y-cable and was invented by Joerg Reisenweber. For additional info and circuit diagrams see Specialized USB Cables.

  • Connect 0V, d+, d-, +5 to your USB device
  • Connect a 15k ohm resistor between d+ and ground
  • Connect a 15k ohm resistor between d- and ground
  • Connect 0V, +5 to your >1A power source
    • If your power source was not the Openmoko 1A charger, additionally connect a 47K ohm 5% resistor between the ID pin and ground to pretend to be the 1A charger.

In addition you need to make sure EN_USBHOST signal that enables the physical Host mode power generation and disables the USB -> PMU charging path is deasserted. This may be taken care of automatically shortly by detection of the 48K resistor on a USB insertion leading to forcing EN_USBHOST deasserted. The charge pump that generates the 5V in host mode doesn't seem to mind getting external 5V given to it, but the real issue is that the battery will not be charged at all if we leave EN_USBHOST asserted since one of its jobs is to stop that happening.

USB Device

The USB Device controller is inside the S3C2442

I2C Devices

I2C is a simple communication standard intended to move small amounts of data a few inches between chips. Please see Neo I2C Devices for more information & a list of devices & the addresses currently in use & documented for the Neo1973.

Audio

See also: Neo1973 Audio Subsystem

Wolfson Codec

There's a WM8753 Wolfson Microelectronics CODEC (This is not a 'smart' codec that can interpret MP3/... it is a simple dumb 'sound card'.)

Mono Amplifier

There's a National Semiconductor LM4853 Mono Amplifier at the analog audio output of the WM8753

  • Product Homepage: LM4853.html
  • Data Sheet: LM4853.pdf
  • Connects to (LM4853 pin):
    • S3C2442 GPIO: HP_IN, AMP_SHUT (shutdown);
    • Wolfson WM8753: LOUTL (LEFTIN), LOUTR (RIGHTIN);
    • speaker4102: (LEFTOUT/BLTOUT-, BLTOUT+);
    • headset-jack: ring 2 (RIGHTOUT), ring 3 (LEFTOUT/BLTOUT-) via 1uF-33R each

Analog wired Headset

There's a four-ring 2.5mm stereo jack which provides connectivity to old-fashioned wired headsets.

The headsets used by Motorola smartphones (A780,A1200, ...) and the V-360 have a compatible configuration, as does the headset for an LG muziq 570.

ring
1(base): GND
2: left out
3: right out
4(tip): mic + HOLD-button(press:short to GND)

Buttons

The Neo1973 GTA02 features two buttons:

Case

The case for the FreeRunner is all black, as seen on the front page of the wiki.

Openmoko has released the CAD files for the case of the Neo1973 and Neo FreeRunner. These were created using Pro/ENGINEER (also called Pro/E). They are available in the Pro/E (.asm/.prt) format, but alternative formats are also available.


We welcome your assistance in providing other formats. If you are able to convert CAD files from Pro/E format to other formats, please contact [1]. We are especially interested in the DXF format and in images rendered from these files.

Browse CAD directory

Accessory

Stylus

Using 4-in-1 laser pen

Battery

The Neo FreeRunner (GTA02) Battery is mechanically and electrically compatible with the Neo1973 GTA01 Battery, as well as limited compatibility with a Nokia BL6C battery. According to this post on the mailinglist. Photo of the battery inside the Neo1973.

microSD Card

GTA02 should come with one of following microSD card

Charger

AKII Technology Charger

  • Model: A10P1-05MP
  • Input: 100-240v~ /0.3A
  • Output: +5v up to 2.0A
  • Add 47.5k 1% resistor between ID pin and ground for openmoko charger identification

Hardware revision history

Main article: GTA02 revisions


Debug Board

Debug Board Connector definition

This is the connector used to connect the Debug Board and possibly other hardware.

Connections are:

  • 39 - GND
  • 38 - STDI
  • 37 - _RESET
  • 36 - STMS
  • 35 - STCK
  • 34 - STDO
  • 33 - GSM_EN
  • 29 - _STRST
  • 19 - X_I2C_SCL (H-TP4703)
  • 18 - X_I2C_SDA (H-TP4704)
  • 17 - SPI_CLK0
  • 16 - SPI_MOSI0
  • 15 - SPI-MISO0
  • 14 - SS0
  • 13 - EINT3 (H-TP4705)
  • 3 - CONSOLE_TXD (H-TP4701)
  • 2 - CONSOLE_RXD (H-TP4702)

Information from [2].

Distinguishing hardware revisions

Inside the Bootloader

Mass production devices (A5 and later)

The bootloader reads the hardware revision from the PCB.[3]

Prototypes (A4 and earlier)

Every hardware revision has its own u-boot image type. Thus, the bootloader has the revision hard-coded. The hardware revision is passed on to the kernel via the ATAG mechanism (ATAG_REVISION)

Inside the Kernel

Mass production devices (A5 and later)

The kernel reads the hardware revision from the PCB.[4]

Prototypes (A4 and earlier)

The kernel receives the ATAG_REVISION during bootup, and saves its contents in the "system_rev" global variable.

From Userspace

The kernel exports the system_rev variable in /proc/cpuinfo as "Revision :" line.

Certification

FCC

CE

NCC

Personal tools


Key pages on:
Neo FreeRunner


The Neo FreeRunner phone is the second hardware platform to take advantage of the Openmoko software stack. You can find specifications of the hardware by reviewing this introduction page and the pages in the category as shown at the bottom of this page.

For basic details please see the Customer-oriented specifications.

Photos


Features

  • Display- Topply o2.8, 480 x 640 pixels, VGA, 200 NIT minimum, resistance type touch
  • User Interface Navigation- Touch screen on LCD, 2 control “buttons”, 1 Power button, 1 Aux for 911 emergency call
  • Built-in 802.11b/g Radio (Atheros chipset AR6001 Flash version)
  • Built-in Bluetooth 2.0 + EDR (CSR and support PCM audio , BC4 firmware version)
  • Built-in 2D/3D graphics acceleration chip (S-Media 3362)
  • 2 built-in Tri-Axis sensors (ST accelerometer LIS302DL)
  • Built-in GPS Radio – -130 dBm with internal antenna, -157 dBm tracking on chipset specification, TTFF under 40 seconds with -130 dBm signal strength, and tracking (u-Blox)
  • Antenna – Specialized antenna for best in hand hold GPS, GPRS and Wi-Fi/Bluetooth performance are required, -105dBm on receiving, Tx 30dbm+2 on GSM
  • External Antennae – MMCX GPS connector
  • GPRS Radio –GSM/GPRS radio. A Pre-PTCRB certified module will be preferred
  • Linux – Linux kernel 2.6.24 or later Openmoko kernel
  • USB - Client and Host-mode switchable (to be used for software downloading), provide host 5V power
  • Power- Normal mode power will be via 1200 mAh battery with built-in coulomb counter, could charge via specialized charger. Internal Lithium Ion or Lithium Polymer battery will keep device in standby mode. Battery life (Approximation/Ideal Target) Standby time 70h Hrs (GSM) Talk time (Backlight off) Up to 3-4 hrs(GSM)
  • LED- LED indicator under Aux/Power button key

Hardware Specification

Full schematics are available.

Hardware Electrical

  • 400/500 MHz Samsung 2442B Processor/SOC (400 minimum, ARM920T core, ARMv4T)
  • Unbrickable dual Boot code in NAND FLASH and 2MB NOR FLASH
  • 128 MB SDRAM total, 64 MB CPU internal, 64 MB external
  • 256MB NAND Flash MCP package.

Display

  • Topploy VGA, 16 bit color depth
  • resolution: 480 x 640 pixels
  • size: 43mm x 58mm (1.7” x 2.27”)
  • diagonal: 72.2mm (2.84”)
  • Transmissive display: good readability in high ambient light is essential
  • White LED backlight. Required brightness is 200 NIT minimum.
  • Resistance type touch panel.

WiFi 802.11 b/g transceiver

  • Must have GPL support source or GPL compatible policy
  • TX power at 11 Mbps: 13 dBm minimum
  • RX sensitivity at 11 Mbps: -89 dBm desired, -83 dBm minimum
  • AP mode desirable, not required
  • WEP and WPA supported
  • Atheros preferred because of its GPL policy

Serial interfaces (UART)

  • Three serial interfaces are required
  • Console
  • A-GPS or GPS
  • GSM/GPRS

Accelerometer

  • 2x accelerometer required
  • Could support interrupt while suspend or power save mode
  • 3 axis sensing

A-GPS

  • GPS chipset receiver and antenna
  • Sensitivity at Antenna port: -157 dBm tracking on chipset specification
  • LNA and SAW filter for maximum interference protection
  • Cold start time to first fix: 40 sec typical at -130 dBm, 60 sec max
  • Must support GPL for Assist-GPS function with open API
  • Industry quality GPS
  • Could fit in GTA01 GPS area on the PCB

GPS Antenna Performance

  • Antenna is passive and internal; 15 mm x 15 mm ceramic patch is nominal design
  • Antenna LNA and SAW filter are required to meet GPS performance
  • 15 mm square ground plane (minimum 1 mm ground border around patch) (TBA)
  • There will be one external GPS antenna connector (MMCX)
  • C/N ratio should higher than 35 on production testing

Buttons

  • Touch screen over LCD is primary data entry mechanism
  • Two “hard” buttons: Power button (on side of Neo1973) is a mechanical switch actuated by a plastic pushbutton in a hole in the housing. Aux (911) button on the top of the device, both of these buttons, when pushed by the operator, are binary inputs (on/off or pressed/not pressed) to the software. The effect of each button is determined by the application software in the device
  • Buttons may need to be backlit
  • 50000 cycles on hardware specification

Sound outputs

  • Speaker in box (need good volume and acoustic behavior in noisy environments)
  • Audio is monophonic
  • Max volume: 100 dB at 5 cm to assure good performance in environment.
  • Support earphone with mic by jack

Power Design Requirements

  • Software-based power management unit preferred
  • NXP PCF series preferred
  • Need support charge from USB function
  • Need support powered by USB function
  • Power switch: Neo1973 will have a power switch, for power on/off and suspend
  • Power/Aux switch must be backlit
  • Switch controls whether device is running or suspended by presses of the switch
  • Switch does not shut off the power; it only suspends/resumes the device
  • Internal Li-Ion or Li-Polymer battery is included. This battery supplies standby power to the device eliminates the rebooting of the device when local power is again reapplied. Battery is 1200 ma-hr.
  • Battery life (Approximation) Ideal/Target Standby time 150-200 Hrs (GSM) Talk time (Backlight off) Up to 4 hrs(GSM)
  • Estimated current draw for the entire device when in suspend mode (and ALL peripherals are turned off or set for deep sleep) is <5 mA at 3.6 volts (Li-Ion terminal voltage).
  • GSM module deep sleep(alive and keep contact with base station) stage should take less than 8mA
  • Battery will reach half capacity (~600 mAh) with 500 charge-discharge cycles. This will occur in less than 2 years of daily service.
  • When powered continuously, Neo1973 must suspend (to low power mode) based either on observed low battery voltage condition or a configurable time delay.
  • Neo1973 must monitor battery status while suspended and resume automatically if the charger is inserted.
  • Primary power connection: 1200mAh battery
  • USB charger have ID pin 47.5k pull down for Openmoko identification
  • Indicators: an LED indicator visible from the side of the unit will illuminate when charging or have missing incoming call

GSM/GPRS

  • 850/1800/1900 and 900/1800/1900 MHz bands must be supported
  • Design should allow for multi-band version (850/900 MHz)
  • Module based GPRS transceiver could meet PTCRB and appropriate FCC certifications. It preferred that the module be pre-certified with PTCRB or OTA test
  • FCC/CE certification required for GSM/GPRS part

GSM-GPRS Antenna Performance

  • -105 dBm receiving on each channel (GSM/PCS)
  • 30+2 dBm transmission on GSM channel

SD card reader

  • One micro-SD card reader, compatible with SD and SDHC.

A small speed test can be found on the StorageSpeed page.

Wi-Fi Modules

  • Must support GPL driver
  • Atheros AR6k preferred
  • Flash version required

Wi-Fi Antenna Performance

  • The Wi-Fi antenna with TX 13 to 15 dBm
  • RX -89 to -83 dBm @802.11b 11Mbps or an equivalent performance antenna

Bluetooth

  • CSR BC4 or later solutions

USB

  • Neo FreeRunner GTA02 will have USB, client/host. Using USB 1.1
  • Provides USB host 5v power
  • Could be powered by USB

Microphone

1 microphone is in the device

Firmware Image

  • Using Linux 2.6.24 or later
  • Could support booting from NAND or from NOR
  • Shipping image should come with basic phone function
  • Could do full firmware upgrade by USB cable

PSN

  • Device will have a PSN (product serial number) printed on the product label and machine readable in system NAND memory

IMEI

  • Production phase should have IMEI code written

Package Specification

  • Weight: ~133 grams with battery.
  • 4-in-1 laser pen passed RoHs and safety regulation for laser equipment safety
  • 1x 512MB microSD Card (SanDisk / Transcend TS512MUSD)
  • 1x USB cable Standard A to mini-B connector
  • 1x 1200mAh smart/gauge battery
  • Quick start guide
  • 5v USB power cord w/100-240 switchable power plug
  • Safety card, warranty card
  • Package could pass 1m to 1.5m drop test
  • AC USB charger,100v-240v, Passed UL and all required safety regulations
  • Must pass FCC/CE certification
  • Must pass NCC certification for Taiwan import regulation
  • RoHS Compatible
  • WEEE Report required

Life Cycle Specification

Product Life

The product is designed to last a minimum of 2 years.

Operating Temperature

  • Target operating range is –10°C to +60°C

Storage Temperature

  • -15 deg C to +70 deg C

ESD

The device can withstand a 4.0kV contact discharge and 8.0kV air

Drop test

Should pass 1m direct drop to concrete ground or 1.5m on slide with carpet


GTA02 Hardware Component Selection

Physical Dimensions

  • 120.7 x 62.0 x 18.5 mm (4.752 x 2.441 x 0.728 inch)
  • 110 +/- 5 g (4 ounces) without battery

Main components

Processor

The main Processor (CPU) of the Neo1973 GTA02 is a Samsung S3C2442B B54 (running at 400 MHz)

Power Management

A NXP PCF50633 04 N3 is used for power management.

Flash

NAND Flash

256MB integrated Samsung NAND flash inside the 2442 multi-chip package, attached to the S3C2442 NAND controller

  • Product Homepage: S3C2442
  • Data Sheet: S3C2442 B54 comes with 256 MB NAND MCP package
  • Connected to: S3C2442 NAND controller

NOR Flash

16MBit ST M58WR016KB706E NOR flash for 'unbrickable emergency boot' feature.

SDRAM

128MB SDRAM (64MB inside 2442 MCP, 1x Samsung K4M51323PC) attached to S3C2442 SDRAM controller

GSM/GPRS

The GSM (including GPRS) modem is Texas Instruments Calypso based and supports 2.5G tri-band GPRS/GSM. The two available models support either the 850/1800/1900 MHz bands (suitable for USA), or 900/1800/1900 MHz band (suitable for rest of the world).

CALYPSO ASIC digital baseband

Unfortunately we cannot provide many details on the GSM chipset due to very tight NDAs. However, this is not neccessarily required, since it interfaces using a standard UART serial line with the S3C2442. On that interface, GSM 07.05, GSM 07.10 and other standardized protocols are used.

The NDAd documentation for the calypso, register definition and hardware definition was leaked onto a public forum on the 4th of March by persons or persons unknown. The legality of reading these files may vary according to your local laws, as may generating code from them.


  • Calypso D751992AZHH
  • The firmware within GTA02 should be moko6 or later (internal code name)

TI TWL3025BZGMR analog baseband

TI TRF6151 (GSM/PCS) RF Transceiver

GPRS Class12/CS4

AGPS

u-blox ANTARIS 4 chip

  • Connected to: S3C2442 UART2, /dev/ttySAC1 in userspace
  • Driver: none needed, talks standard NMEA
  • u-blox Antaris 4 Protocol Protocol download page
  • ATR0635 Datasheet: u-blox ATR0635

Accelerometers

Two ST LIS302DL

Graphics/3D Acceleration

Smedia Glamo 3362.

microSD

The GTA02 has one microSD aka Transflash slot. Using the Glamo 3362 MMC/SD controller

LCD Module (LCM)

Toppoly (tpo) 2.8" diagonal (1.7" x 2.27" - 43mm x 58mm) 480x640 TD028TTEC1 module, using a Toshiba JBT6K74 TFT LCD Driver Chipset.

Touch Screen

Bluetooth Module

Delta DFBM-CS320 Class2 Module, using CSR BlueCore4

Bluetooth Audio

This one is wired via PCM bus from the CSR Bluetooth chip to the Wolfson codec.

WiFi Module

Accton (WLAN 802.11b/g SiP-M WM3236AQ(Flash Ver:2.0 Atheros AR6001GZ)

Vibrator

USB Host

The USB Host controller is inside the S3C2442

  • Driver: Stock Linux kernel ohci_hcd
  • USB version 1.1
  • Supply USB 5v in Host mode using usb power switch AAT1275IRN-5.0-T1
  • A net EN_USBHOST is controlled by PMU GPIO "GPO", this one signal when asserted (high)
    • enables generation of 5V for external device using a charge pump
    • enables connection of 15K pulldowns to D+ and D- to allow device insertion and removal detection for host mode
    • DISABLES the path for USB power to charge the battery

It should also be possible to use host mode with externally-provided power. This will allow the FreeRunner to be connected to a USB device and be powered and charging the battery if present at the same time. This method is called the Y-cable and was invented by Joerg Reisenweber. For additional info and circuit diagrams see Specialized USB Cables.

  • Connect 0V, d+, d-, +5 to your USB device
  • Connect a 15k ohm resistor between d+ and ground
  • Connect a 15k ohm resistor between d- and ground
  • Connect 0V, +5 to your >1A power source
    • If your power source was not the Openmoko 1A charger, additionally connect a 47K ohm 5% resistor between the ID pin and ground to pretend to be the 1A charger.

In addition you need to make sure EN_USBHOST signal that enables the physical Host mode power generation and disables the USB -> PMU charging path is deasserted. This may be taken care of automatically shortly by detection of the 48K resistor on a USB insertion leading to forcing EN_USBHOST deasserted. The charge pump that generates the 5V in host mode doesn't seem to mind getting external 5V given to it, but the real issue is that the battery will not be charged at all if we leave EN_USBHOST asserted since one of its jobs is to stop that happening.

USB Device

The USB Device controller is inside the S3C2442

I2C Devices

I2C is a simple communication standard intended to move small amounts of data a few inches between chips. Please see Neo I2C Devices for more information & a list of devices & the addresses currently in use & documented for the Neo1973.

Audio

See also: Neo1973 Audio Subsystem

Wolfson Codec

There's a WM8753 Wolfson Microelectronics CODEC (This is not a 'smart' codec that can interpret MP3/... it is a simple dumb 'sound card'.)

Mono Amplifier

There's a National Semiconductor LM4853 Mono Amplifier at the analog audio output of the WM8753

  • Product Homepage: LM4853.html
  • Data Sheet: LM4853.pdf
  • Connects to (LM4853 pin):
    • S3C2442 GPIO: HP_IN, AMP_SHUT (shutdown);
    • Wolfson WM8753: LOUTL (LEFTIN), LOUTR (RIGHTIN);
    • speaker4102: (LEFTOUT/BLTOUT-, BLTOUT+);
    • headset-jack: ring 2 (RIGHTOUT), ring 3 (LEFTOUT/BLTOUT-) via 1uF-33R each

Analog wired Headset

There's a four-ring 2.5mm stereo jack which provides connectivity to old-fashioned wired headsets.

The headsets used by Motorola smartphones (A780,A1200, ...) and the V-360 have a compatible configuration, as does the headset for an LG muziq 570.

ring
1(base): GND
2: left out
3: right out
4(tip): mic + HOLD-button(press:short to GND)

Buttons

The Neo1973 GTA02 features two buttons:

Case

The case for the FreeRunner is all black, as seen on the front page of the wiki.

Openmoko has released the CAD files for the case of the Neo1973 and Neo FreeRunner. These were created using Pro/ENGINEER (also called Pro/E). They are available in the Pro/E (.asm/.prt) format, but alternative formats are also available.


We welcome your assistance in providing other formats. If you are able to convert CAD files from Pro/E format to other formats, please contact [1]. We are especially interested in the DXF format and in images rendered from these files.

Browse CAD directory

Accessory

Stylus

Using 4-in-1 laser pen

Battery

The Neo FreeRunner (GTA02) Battery is mechanically and electrically compatible with the Neo1973 GTA01 Battery, as well as limited compatibility with a Nokia BL6C battery. According to this post on the mailinglist. Photo of the battery inside the Neo1973.

microSD Card

GTA02 should come with one of following microSD card

Charger

AKII Technology Charger

  • Model: A10P1-05MP
  • Input: 100-240v~ /0.3A
  • Output: +5v up to 2.0A
  • Add 47.5k 1% resistor between ID pin and ground for openmoko charger identification

Hardware revision history

Main article: GTA02 revisions


Debug Board

Debug Board Connector definition

This is the connector used to connect the Debug Board and possibly other hardware.

Connections are:

  • 39 - GND
  • 38 - STDI
  • 37 - _RESET
  • 36 - STMS
  • 35 - STCK
  • 34 - STDO
  • 33 - GSM_EN
  • 29 - _STRST
  • 19 - X_I2C_SCL (H-TP4703)
  • 18 - X_I2C_SDA (H-TP4704)
  • 17 - SPI_CLK0
  • 16 - SPI_MOSI0
  • 15 - SPI-MISO0
  • 14 - SS0
  • 13 - EINT3 (H-TP4705)
  • 3 - CONSOLE_TXD (H-TP4701)
  • 2 - CONSOLE_RXD (H-TP4702)

Information from [2].

Distinguishing hardware revisions

Inside the Bootloader

Mass production devices (A5 and later)

The bootloader reads the hardware revision from the PCB.[3]

Prototypes (A4 and earlier)

Every hardware revision has its own u-boot image type. Thus, the bootloader has the revision hard-coded. The hardware revision is passed on to the kernel via the ATAG mechanism (ATAG_REVISION)

Inside the Kernel

Mass production devices (A5 and later)

The kernel reads the hardware revision from the PCB.[4]

Prototypes (A4 and earlier)

The kernel receives the ATAG_REVISION during bootup, and saves its contents in the "system_rev" global variable.

From Userspace

The kernel exports the system_rev variable in /proc/cpuinfo as "Revision :" line.

Certification

FCC

CE

NCC