Neo FreeRunner GTA02 Hardware/ru

From Openmoko

Revision as of 13:48, 31 August 2008 by DolfjeBot1 (Talk | contribs)

Jump to: navigation, search



Openmoko - это стек программного обеспечения, которое работает поверх аппаратной платформы. Смартфон Neo FreeRunner - это аппаратная платформа второго поколения, которая использует Openmoko. Вы можете получить сведения относительно характериск аппаратной части, просмотрев эту вводную страницу, а также другие страницы в этой категории, приведенные в нижней части этой страницы.


Резюме

Openmoko, Inc. создает основанный на GNU/Linux смартфон применяя для Openmoko микропрограммное обеспечение с исходным кодом, полностью совместимым с условиями лицензии GPL. Кодовое имя проекта GTA02 (Neo FreeRunner).

Детально аппаратные компоненты рассматриваются далее. См. также Neo FreeRunner GTA02 Hardware Requirements\ru используемые для выбора этих компонентов.

Расположение элементов на печатной плате

Gta02a5 pcba cs1.png

1. NOR Flash
2. SDRAM
3. GPS
4. CPU/NAND Flash
5. GPU
6. PMU
7. Audio Codec

8. Addio Amplifier
9. USB Host Power
10. Analog Baseband
11. Digital Baseband
12. GSM SRAM/Flash
13. GSM RF TRanceiver
14. RF AMP

Аппаратные компоненты GTA02

Габаритные размеры

  • 120.7 x 62 x 18.5 мм (4.75 x 2.44 x 0.728 дюйма)
  • 110 +/- 5 г (4 унции) без батареи

Основные компоненты

Процессор

Центральный процессор (CPU) это Samsung S3C2442B B54 (работающий на частоте 400 MHz)

Назначение выводов (GPIO): https://svn.openmoko.org/trunk/doc/hardware/GTA02v4/gpio.txt


Управление питанием

A NXP PCF50633 04 N3 is used for power management.

Flash

NAND Flash

256MB integrated Samsung NAND flash inside the 2442 multi-chip package, attached to the S3C2442 NAND controller

  • Product Homepage: S3C2442
  • Data Sheet: S3C2442 B54 comes with 256 MB NAND MCP package
  • Connected to: S3C2442 NAND controller

NOR Flash

16MBit ST M58WR016KB706E NOR flash for 'unbrickable emergency boot' feature.

SDRAM

128MB SDRAM (64MB inside 2442 MCP, 1x Samsung K4M51323PC) attached to S3C2442 SDRAM controller

GSM/GPRS

The GSM (including GPRS) modem is Texas Instruments Calypso based.

Цифровой модулятор CALYPSO ASIC

Unfortunately we cannot provide many details on the GSM chipset due to very tight NDAs. However, this is not neccessarily required, since it interfaces using a standard UART serial line with the S3C2442. On that interface, GSM 07.05, GSM 07.10 and other standardized protocols are used.

The NDAd documentation for the calypso, register definition and hardware definition was leaked onto a public forum on the 4th of March by persons or persons unknown. The legality of reading these files may vary according to your local laws, as may generating code from them.


  • Calypso D751992AZHH
  • The firmware within GTA02 should be moko6 or later (internal code name)

Аналоговый модулятор TI TWL3025BZGMR

TI TRF6151 (GSM/PCS) RF трансивер

GPRS Class12/CS4

AGPS

u-blox ANTARIS 4 chip

  • Connected to: S3C2442 UART2, /dev/ttySAC1 in userspace
  • Driver: none needed, talks standard NMEA
  • u-blox Antaris 4 Protocol Protocol download page
  • ATR0635 Datasheet: u-blox ATR0635

Акселерометры

Two ST LIS302DL

Графическое/3D ускорение

Smedia Glamo 3362.

microSD

The GTA02 has one microSD aka Transflash slot. Using the Glamo 3362 MMC/SD controller

LCD модуль (LCM)

Toppoly (tpo) 2.8" diagonal (1.7" x 2.27" - 43mm x 58mm) 480x640 TD028TTEC1 module, using a Toshiba JBT6K74 TFT LCD Driver Chipset.

Сенсорный экран

Модуль Bluetooth

Delta DFBM-CS320 Class2 Module, using CSR BlueCore4

Bluetooth аудио

This one is wired via PCM bus from the CSR Bluetooth chip to the Wolfson codec.

Модуль WiFi

Accton (WLAN 802.11b/g SiP-M WM3236AQ(Flash Ver:2.0 Atheros AR6001GZ)

Виброзвонок

Хост USB

The USB Host controller is inside the S3C2442

  • Driver: Stock Linux kernel ohci_hcd
  • USB version 1.1
  • Supply USB 5v in Host mode using usb power switch AAT1275IRN-5.0-T1
  • A net EN_USBHOST is controlled by PMU GPIO "GPO", this one signal when asserted (high)
    • enables generation of 5V for external device using a charge pump
    • enables connection of 15K pulldowns to D+ and D- to allow device insertion and removal detection for host mode
    • DISABLES the path for USB power to charge the battery

It should also be possible to use host mode with externally-provided power. This will allow the FreeRunner to be connected to a USB device and be powered and charging the battery if present at the same time.

  • Connect 0V, d+, d-, +5 to your USB device
  • Connect a 15k ohm resistor between d+ and ground
  • Connect a 15k ohm resistor between d- and ground
  • Connect 0V, +5 to your >1A power source
    • If your power source was not the Openmoko 1A charger, additionally connect a 47K ohm 5% resistor between the ID pin and ground to pretend to be the 1A charger.

In addition you need to make sure EN_USBHOST signal that enables the physical Host mode power generation and disables the USB -> PMU charging path is deasserted. This may be taken care of automatically shortly by detection of the 48K resistor on a USB insertion leading to forcing EN_USBHOST deasserted. The charge pump that generates the 5V in host mode doesn't seem to mind getting external 5V given to it, but the real issue is that the battery will not be charged at all if we leave EN_USBHOST asserted since one of its jobs is to stop that happening.

Устройство USB

The USB Device controller is inside the S3C2442

Устройство I2C

I2C is a simple communication standard intended to move small amounts of data a few inches between chips. Please see Neo I2C Devices for more information & a list of devices & the addresses currently in use & documented for the Neo1973.

Аудио

See also: Neo1973 Audio Subsystem

Кодек Wolfson

There's a WM8753 Wolfson Microelectronics CODEC (This is not a 'smart' codec that can interpret MP3/... it is a simple dumb 'sound card'.

Монофонический усилитель

There's a National Semiconductor LM4853 Mono Amplifier at the analog audio output of the WM8753

  • Product Homepage: LM4853.html
  • Data Sheet: LM4853.pdf
  • Connects to (LM4853 pin):
    • S3C2442 GPIO: HP_IN, AMP_SHUT (shutdown);
    • Wolfson WM8753: LOUTL (LEFTIN), LOUTR (RIGHTIN);
    • speaker4102: (LEFTOUT/BLTOUT-, BLTOUT+);
    • headset-jack: ring 2 (RIGHTOUT), ring 3 (LEFTOUT/BLTOUT-) via 1uF-33R each

Аналоговые проводные наушники

There's a four-ring 2.5mm stereo jack which provides connectivity to old-fashioned wired headsets.

The headsets used by Motorola smartphones (A780,A1200, ...) and the V-360 have a compatible configuration.

ring
1(base): GND
2: right out
3: left out
4(tip): mic + HOLD-button(press:short to GND)

Кнопочки

The Neo1973 GTA02 features two buttons:

Корпус

The case for the FreeRunner is all black, as seen on the front page of the wiki.

Openmoko has released the CAD files for the case schematics for the Openmoko Neo1973 (GTA01) and Neo FreeRunner. These are available in the original Pro/E (.asm/.prt) format and alternative formats created from the originals.

We welcome your assistance in providing other formats. If you are able to convert CAD files from Pro/E format to other formats, please contact [1]. We are especially interested in the DXF format and in images rendered from these files.

Browse CAD directory

Аксессуары

Стилус

Using 4 in 1 laser pen

Батарея

The Neo FreeRunner (GTA02) Battery is mechanically and electrically compatible with the Neo1973 GTA01 Battery, as well as limited compatibility with a Nokia BL6C battery. According to this post on the mailinglist. Photo of the battery inside the Neo1973.

Карта microSD

GTA02 should come with one of following microSD card

Зарядное устройство

AKII Technology Charger

  • Model: A10P1-05MP
  • Input: 100-240v~ /0.3A
  • Output: +5v up to 2.0A
  • Add 47.5k 1% resistor between ID pin and ground for openmoko charger identification

История

GTA02v1

First generation of prototypes that was given to internal Openmoko software developers. Total 30 pcs fabricated.

  • It is working just fine, but still based on 2440, with external NAND/SDRAM and no NOR flash
  • Using the PCF50633 05 N3 due to 04 N3 not available, re-work power for basic schematics verification
  • Using GTA01 SIM socket
  • Add external debug port
  • Still using Global locate A-GPS
  • ATAG_REVISION: 0310

GTA02v2

Second generation of prototypes, Total 50 pcs run at Taipei SMT factory MOUNT

  • Ideal is have 256 MB NAND on Samsung package, Due to chip availability Start using S3C2442 B43
  • Using correct PMU PCF50633 04 N3
  • Change new SIM socket
  • Change to u-blox A-GPS
  • Change LCM power from 3.3v to 1.8v
  • USB power switch layout/pin assignment mistake, could not verify USB host supply 5v function
  • GPS function verified ok with good sensitivity
  • ATAG_REVISION: 0320

GTA02v3

Production verification version, 2007/10/11 28 pcs fabricate at FIC SuZhou

  • Still using S3C2442 B43 for hardware verification
  • Using control pilot run to verify S3C2442 B54 chips
  • ATAG_REVISION: 0330

GTA02v4

Mass production release candidate version 1

2 weeks after v3 gerber out, release the v4 gerber, and 2007/10/20 20 pcs fabricate at FIC SuZhou

  • Change LCM power from 1.8v to 3.3v for display stability issue
  • fabricate another 200 pcs for yield rate/production verification
  • fabricate 50 pcs with S3C2442 B43 (128 MB NAND) for quality comparsion
  • USB host power chip have some output voltage stability issues with Vb/Vcc comes from different power source, need layout change to fix the issue
  • Battery Coulomb design not working on A4
  • ATAG_REVISION: 0340

GTA02v5

Mass production candidate version 2/Mass production version

  • First batch fabricate 2008/1/14 at FIC SuZhou
  • Mass production A5 trial run start from 2008 March, including some resistor/capacitor change compare with inital 100 pcs prototypes A5, and prototypes for GTA02 developers was tracked in the Prototypes Page
  • Coulomb counter issue fixed
  • USB host power switch fixed
  • Need add capacitor for PMU Vbat input for stability issue, this could be done by direct SMT or hand rework
  • Need rework (still using SMT in production) add capacitor for PMU Vbat input for PMU stability issue.
  • Need manual rework GSM IR UART path a 100k pull down for better GSM deep sleep
  • ATAG_REVISION: 0350

GTA02 mass Production version change list

  • PMU's LED power error: PMU potential damage issue
  • NOR FLASH enable WP: User can write data into NOR FLASH.
  • CE CS/RS fine tune: Audio's background noise too high
  • I2C pull high resistor: The resistor is too high and signal is distorted
  • GSM leakage current: TX_MODEM has a pull high resistor on IO_3V3
  • Power consumption: Disable keep active function
  • SDIO clock and esd protect resistor
  • Refer to Datasheet: R1526 to 33K
  • GSM modem on pin: The R1018 is too small and has some leakage current
  • LED driving transistor: When GPIO is on, the transistor will be draw more current on LED. This is component change fix, do not need change PCB or re-work.

GTA02v6

Mass production candidate version 3/Mass production version

A6 will be fine tune version of A5, only minor schematic change for better product quality and version control. Capacitor and resistor change A6 also on mass production A5

  • First 100 pcs start from 2008 mid April, and factory make component placement mistake on GSM, second 100 pcs PCB arrive time TBD.
  • Add capacitor space for Vbat, reduce the SMT effort
  • Add GSM IR resistor for better GSM deep sleep
  • Reserve 3 GPIO for hardware version control
  • Fixed LEDs power usage (from about 150mW of v5 to about 25mW)
  • ATAG_REVISION: 0360

GTA02 A5 to A6 changes

  • Power Glitch on VB_SYS: Add capacitor on layout, Mass production A5 also apply this change.
  • G-sensor separate these interrupt pins: At A5, each accelerometer INT1/INT2 connected to same line, at A6 only INT1 was connected.
  • GSM_modem power source Reduce power's ripple when the phone is talking
  • Keep active Disable keep active function, just fine tune
  • GPIO for version control
  • GSM RX_IR has some noise Add resistor and reduce GSM RX_IR noise and gsm can't enter suspend mode easily, apply on mass production A5.
  • LED driving transistor apply on mass production A5.
  • LCM's VDDIO We can totally power off LCM's power, save about extra 1mA.

Отладочная плата

Описание соединения отладочной платы

This is the connector used to connect the Debug Board and possibly other hardware.

Connections are:

  • 39 - GND
  • 38 - STDI
  • 37 - _RESET
  • 36 - STMS
  • 35 - STCK
  • 34 - STDO
  • 33 - GSM_EN
  • 29 - _STRST
  • 19 - X_I2C_SCL (H-TP4703)
  • 18 - X_I2C_SDA (H-TP4704)
  • 17 - SPI_CLK0
  • 16 - SPI_MOSI0
  • 15 - SPI-MISO0
  • 14 - SS0
  • 13 - EINT3 (H-TP4705)
  • 3 - CONSOLE_TXD (H-TP4701)
  • 2 - CONSOLE_RXD (H-TP4702)

Information from [2].

Отличия аппаратных изменений

Inside the Bootloader

Every hardware revision has its own u-boot image type. Thus, the bootloader has the revision hard-coded. The hardware revision is passed on to the kernel via the ATAG mechanism (ATAG_REVISION)

Inside the Kernel

The kernel receives the ATAG_REVISION during bootup, and saves its contents in the "system_rev" global variable.

From Userspace

The kernel exports the system_rev variable in /proc/cpuinfo as "Revision :" line.

Certification

FCC

CE

NCC

Personal tools


Key pages on:
Neo FreeRunner


Openmoko - это стек программного обеспечения, которое работает поверх аппаратной платформы. Смартфон Neo FreeRunner - это аппаратная платформа второго поколения, которая использует Openmoko. Вы можете получить сведения относительно характериск аппаратной части, просмотрев эту вводную страницу, а также другие страницы в этой категории, приведенные в нижней части этой страницы.


Резюме

Openmoko, Inc. создает основанный на GNU/Linux смартфон применяя для Openmoko микропрограммное обеспечение с исходным кодом, полностью совместимым с условиями лицензии GPL. Кодовое имя проекта GTA02 (Neo FreeRunner).

Детально аппаратные компоненты рассматриваются далее. См. также Neo FreeRunner GTA02 Hardware Requirements\ru используемые для выбора этих компонентов.

Расположение элементов на печатной плате

Gta02a5 pcba cs1.png

1. NOR Flash
2. SDRAM
3. GPS
4. CPU/NAND Flash
5. GPU
6. PMU
7. Audio Codec

8. Addio Amplifier
9. USB Host Power
10. Analog Baseband
11. Digital Baseband
12. GSM SRAM/Flash
13. GSM RF TRanceiver
14. RF AMP

Аппаратные компоненты GTA02

Габаритные размеры

  • 120.7 x 62 x 18.5 мм (4.75 x 2.44 x 0.728 дюйма)
  • 110 +/- 5 г (4 унции) без батареи

Основные компоненты

Процессор

Центральный процессор (CPU) это Samsung S3C2442B B54 (работающий на частоте 400 MHz)

Назначение выводов (GPIO): https://svn.openmoko.org/trunk/doc/hardware/GTA02v4/gpio.txt


Управление питанием

A NXP PCF50633 04 N3 is used for power management.

Flash

NAND Flash

256MB integrated Samsung NAND flash inside the 2442 multi-chip package, attached to the S3C2442 NAND controller

  • Product Homepage: S3C2442
  • Data Sheet: S3C2442 B54 comes with 256 MB NAND MCP package
  • Connected to: S3C2442 NAND controller

NOR Flash

16MBit ST M58WR016KB706E NOR flash for 'unbrickable emergency boot' feature.

SDRAM

128MB SDRAM (64MB inside 2442 MCP, 1x Samsung K4M51323PC) attached to S3C2442 SDRAM controller

GSM/GPRS

The GSM (including GPRS) modem is Texas Instruments Calypso based.

Цифровой модулятор CALYPSO ASIC

Unfortunately we cannot provide many details on the GSM chipset due to very tight NDAs. However, this is not neccessarily required, since it interfaces using a standard UART serial line with the S3C2442. On that interface, GSM 07.05, GSM 07.10 and other standardized protocols are used.

The NDAd documentation for the calypso, register definition and hardware definition was leaked onto a public forum on the 4th of March by persons or persons unknown. The legality of reading these files may vary according to your local laws, as may generating code from them.


  • Calypso D751992AZHH
  • The firmware within GTA02 should be moko6 or later (internal code name)

Аналоговый модулятор TI TWL3025BZGMR

TI TRF6151 (GSM/PCS) RF трансивер

GPRS Class12/CS4

AGPS

u-blox ANTARIS 4 chip

  • Connected to: S3C2442 UART2, /dev/ttySAC1 in userspace
  • Driver: none needed, talks standard NMEA
  • u-blox Antaris 4 Protocol Protocol download page
  • ATR0635 Datasheet: u-blox ATR0635

Акселерометры

Two ST LIS302DL

Графическое/3D ускорение

Smedia Glamo 3362.

microSD

The GTA02 has one microSD aka Transflash slot. Using the Glamo 3362 MMC/SD controller

LCD модуль (LCM)

Toppoly (tpo) 2.8" diagonal (1.7" x 2.27" - 43mm x 58mm) 480x640 TD028TTEC1 module, using a Toshiba JBT6K74 TFT LCD Driver Chipset.

Сенсорный экран

Модуль Bluetooth

Delta DFBM-CS320 Class2 Module, using CSR BlueCore4

Bluetooth аудио

This one is wired via PCM bus from the CSR Bluetooth chip to the Wolfson codec.

Модуль WiFi

Accton (WLAN 802.11b/g SiP-M WM3236AQ(Flash Ver:2.0 Atheros AR6001GZ)

Виброзвонок

Хост USB

The USB Host controller is inside the S3C2442

  • Driver: Stock Linux kernel ohci_hcd
  • USB version 1.1
  • Supply USB 5v in Host mode using usb power switch AAT1275IRN-5.0-T1
  • A net EN_USBHOST is controlled by PMU GPIO "GPO", this one signal when asserted (high)
    • enables generation of 5V for external device using a charge pump
    • enables connection of 15K pulldowns to D+ and D- to allow device insertion and removal detection for host mode
    • DISABLES the path for USB power to charge the battery

It should also be possible to use host mode with externally-provided power. This will allow the FreeRunner to be connected to a USB device and be powered and charging the battery if present at the same time.

  • Connect 0V, d+, d-, +5 to your USB device
  • Connect a 15k ohm resistor between d+ and ground
  • Connect a 15k ohm resistor between d- and ground
  • Connect 0V, +5 to your >1A power source
    • If your power source was not the Openmoko 1A charger, additionally connect a 47K ohm 5% resistor between the ID pin and ground to pretend to be the 1A charger.

In addition you need to make sure EN_USBHOST signal that enables the physical Host mode power generation and disables the USB -> PMU charging path is deasserted. This may be taken care of automatically shortly by detection of the 48K resistor on a USB insertion leading to forcing EN_USBHOST deasserted. The charge pump that generates the 5V in host mode doesn't seem to mind getting external 5V given to it, but the real issue is that the battery will not be charged at all if we leave EN_USBHOST asserted since one of its jobs is to stop that happening.

Устройство USB

The USB Device controller is inside the S3C2442

Устройство I2C

I2C is a simple communication standard intended to move small amounts of data a few inches between chips. Please see Neo I2C Devices for more information & a list of devices & the addresses currently in use & documented for the Neo1973.

Аудио

See also: Neo1973 Audio Subsystem

Кодек Wolfson

There's a WM8753 Wolfson Microelectronics CODEC (This is not a 'smart' codec that can interpret MP3/... it is a simple dumb 'sound card'.

Монофонический усилитель

There's a National Semiconductor LM4853 Mono Amplifier at the analog audio output of the WM8753

  • Product Homepage: LM4853.html
  • Data Sheet: LM4853.pdf
  • Connects to (LM4853 pin):
    • S3C2442 GPIO: HP_IN, AMP_SHUT (shutdown);
    • Wolfson WM8753: LOUTL (LEFTIN), LOUTR (RIGHTIN);
    • speaker4102: (LEFTOUT/BLTOUT-, BLTOUT+);
    • headset-jack: ring 2 (RIGHTOUT), ring 3 (LEFTOUT/BLTOUT-) via 1uF-33R each

Аналоговые проводные наушники

There's a four-ring 2.5mm stereo jack which provides connectivity to old-fashioned wired headsets.

The headsets used by Motorola smartphones (A780,A1200, ...) and the V-360 have a compatible configuration.

ring
1(base): GND
2: right out
3: left out
4(tip): mic + HOLD-button(press:short to GND)

Кнопочки

The Neo1973 GTA02 features two buttons:

Корпус

The case for the FreeRunner is all black, as seen on the front page of the wiki.

Openmoko has released the CAD files for the case schematics for the Openmoko Neo1973 (GTA01) and Neo FreeRunner. These are available in the original Pro/E (.asm/.prt) format and alternative formats created from the originals.

We welcome your assistance in providing other formats. If you are able to convert CAD files from Pro/E format to other formats, please contact [1]. We are especially interested in the DXF format and in images rendered from these files.

Browse CAD directory

Аксессуары

Стилус

Using 4 in 1 laser pen

Батарея

The Neo FreeRunner (GTA02) Battery is mechanically and electrically compatible with the Neo1973 GTA01 Battery, as well as limited compatibility with a Nokia BL6C battery. According to this post on the mailinglist. Photo of the battery inside the Neo1973.

Карта microSD

GTA02 should come with one of following microSD card

Зарядное устройство

AKII Technology Charger

  • Model: A10P1-05MP
  • Input: 100-240v~ /0.3A
  • Output: +5v up to 2.0A
  • Add 47.5k 1% resistor between ID pin and ground for openmoko charger identification

История

GTA02v1

First generation of prototypes that was given to internal Openmoko software developers. Total 30 pcs fabricated.

  • It is working just fine, but still based on 2440, with external NAND/SDRAM and no NOR flash
  • Using the PCF50633 05 N3 due to 04 N3 not available, re-work power for basic schematics verification
  • Using GTA01 SIM socket
  • Add external debug port
  • Still using Global locate A-GPS
  • ATAG_REVISION: 0310

GTA02v2

Second generation of prototypes, Total 50 pcs run at Taipei SMT factory MOUNT

  • Ideal is have 256 MB NAND on Samsung package, Due to chip availability Start using S3C2442 B43
  • Using correct PMU PCF50633 04 N3
  • Change new SIM socket
  • Change to u-blox A-GPS
  • Change LCM power from 3.3v to 1.8v
  • USB power switch layout/pin assignment mistake, could not verify USB host supply 5v function
  • GPS function verified ok with good sensitivity
  • ATAG_REVISION: 0320

GTA02v3

Production verification version, 2007/10/11 28 pcs fabricate at FIC SuZhou

  • Still using S3C2442 B43 for hardware verification
  • Using control pilot run to verify S3C2442 B54 chips
  • ATAG_REVISION: 0330

GTA02v4

Mass production release candidate version 1

2 weeks after v3 gerber out, release the v4 gerber, and 2007/10/20 20 pcs fabricate at FIC SuZhou

  • Change LCM power from 1.8v to 3.3v for display stability issue
  • fabricate another 200 pcs for yield rate/production verification
  • fabricate 50 pcs with S3C2442 B43 (128 MB NAND) for quality comparsion
  • USB host power chip have some output voltage stability issues with Vb/Vcc comes from different power source, need layout change to fix the issue
  • Battery Coulomb design not working on A4
  • ATAG_REVISION: 0340

GTA02v5

Mass production candidate version 2/Mass production version

  • First batch fabricate 2008/1/14 at FIC SuZhou
  • Mass production A5 trial run start from 2008 March, including some resistor/capacitor change compare with inital 100 pcs prototypes A5, and prototypes for GTA02 developers was tracked in the Prototypes Page
  • Coulomb counter issue fixed
  • USB host power switch fixed
  • Need add capacitor for PMU Vbat input for stability issue, this could be done by direct SMT or hand rework
  • Need rework (still using SMT in production) add capacitor for PMU Vbat input for PMU stability issue.
  • Need manual rework GSM IR UART path a 100k pull down for better GSM deep sleep
  • ATAG_REVISION: 0350

GTA02 mass Production version change list

  • PMU's LED power error: PMU potential damage issue
  • NOR FLASH enable WP: User can write data into NOR FLASH.
  • CE CS/RS fine tune: Audio's background noise too high
  • I2C pull high resistor: The resistor is too high and signal is distorted
  • GSM leakage current: TX_MODEM has a pull high resistor on IO_3V3
  • Power consumption: Disable keep active function
  • SDIO clock and esd protect resistor
  • Refer to Datasheet: R1526 to 33K
  • GSM modem on pin: The R1018 is too small and has some leakage current
  • LED driving transistor: When GPIO is on, the transistor will be draw more current on LED. This is component change fix, do not need change PCB or re-work.

GTA02v6

Mass production candidate version 3/Mass production version

A6 will be fine tune version of A5, only minor schematic change for better product quality and version control. Capacitor and resistor change A6 also on mass production A5

  • First 100 pcs start from 2008 mid April, and factory make component placement mistake on GSM, second 100 pcs PCB arrive time TBD.
  • Add capacitor space for Vbat, reduce the SMT effort
  • Add GSM IR resistor for better GSM deep sleep
  • Reserve 3 GPIO for hardware version control
  • Fixed LEDs power usage (from about 150mW of v5 to about 25mW)
  • ATAG_REVISION: 0360

GTA02 A5 to A6 changes

  • Power Glitch on VB_SYS: Add capacitor on layout, Mass production A5 also apply this change.
  • G-sensor separate these interrupt pins: At A5, each accelerometer INT1/INT2 connected to same line, at A6 only INT1 was connected.
  • GSM_modem power source Reduce power's ripple when the phone is talking
  • Keep active Disable keep active function, just fine tune
  • GPIO for version control
  • GSM RX_IR has some noise Add resistor and reduce GSM RX_IR noise and gsm can't enter suspend mode easily, apply on mass production A5.
  • LED driving transistor apply on mass production A5.
  • LCM's VDDIO We can totally power off LCM's power, save about extra 1mA.

Отладочная плата

Описание соединения отладочной платы

This is the connector used to connect the Debug Board and possibly other hardware.

Connections are:

  • 39 - GND
  • 38 - STDI
  • 37 - _RESET
  • 36 - STMS
  • 35 - STCK
  • 34 - STDO
  • 33 - GSM_EN
  • 29 - _STRST
  • 19 - X_I2C_SCL (H-TP4703)
  • 18 - X_I2C_SDA (H-TP4704)
  • 17 - SPI_CLK0
  • 16 - SPI_MOSI0
  • 15 - SPI-MISO0
  • 14 - SS0
  • 13 - EINT3 (H-TP4705)
  • 3 - CONSOLE_TXD (H-TP4701)
  • 2 - CONSOLE_RXD (H-TP4702)

Information from [2].

Отличия аппаратных изменений

Inside the Bootloader

Every hardware revision has its own u-boot image type. Thus, the bootloader has the revision hard-coded. The hardware revision is passed on to the kernel via the ATAG mechanism (ATAG_REVISION)

Inside the Kernel

The kernel receives the ATAG_REVISION during bootup, and saves its contents in the "system_rev" global variable.

From Userspace

The kernel exports the system_rev variable in /proc/cpuinfo as "Revision :" line.

Certification

FCC

CE

NCC