Neo 1973 Phase 0 - Revision history

Glenn: Exchg bootloader with U-Boot

2012-02-10T08:32:56Z

Exchg bootloader with U-Boot

2008-08-23T08:45:42Z

Replacing 'OpenMoko' with 'Openmoko'

2008-07-13T10:11:44Z

2008-07-06T10:24:39Z

-cats

2008-03-27T04:22:20Z

2008-02-29T07:49:11Z

‎Workaround

2007-07-28T13:38:02Z

2007-07-16T08:10:22Z

topsort

2007-07-13T14:48:09Z

2007-03-22T12:20:50Z

‎Solution: problem

@@ Line 4: / Line 4: @@
 See the following sections for quick start instructions for Phase0 developers:
-* [[Bootloader#Phase0_Quick_Start|Accessing the Bootloader]]
+* [[U-Boot#Phase0_Quick_Start|Accessing the U-Boot]]
 * [[Neo1973_Audio_Subsystem#Phase0_Quick_Start|Playing an MP3 file]]
@@ Line 15: / Line 15: @@
 === Restoring original Software Image ===
-{{note|This is how you do a full restore, including [[bootloader]].  This requires a [[Debug Board]].  In most cases, it is sufficient to use [[dfu-util]] to flash [[kernel]] and rootfs partitions}}
+{{note|This is how you do a full restore, including [[U-Boot]].  This requires a [[Debug Board]].  In most cases, it is sufficient to use [[dfu-util]] to flash [[kernel]] and rootfs partitions}}
 This is how to restore the phone:
@@ Line 93: / Line 93: @@
 Either use the 'pad' option to '''mkfs.jffs2' when creating the image '''or''' use
   GTA01Bv3#  nand erase clean rootfs
-on the bootloader console before using DFU to flash a new rootfs image
+on the U-Boot console before using DFU to flash a new rootfs image
 === Mechanical stress to microSD lid can cause short-circuit ===
@@ Line 135: / Line 135: @@
 Power on the device.
-Then get into the bootloader console via ttyACM0. Then type "neo1973 charger fast".
+Then get into the U-Boot console via ttyACM0. Then type "neo1973 charger fast".
 Alternative: Change battery to [[Neo1973_Battery|BL-5C]] with enough juice.

@@ Line 66: / Line 66: @@
 * the screen goes dark for 1-2 minutes
 * the screen lights up and shows a smiling face for a few minutes
-* the screen goes dark and shows a partial (broken) OpenMoko logo for about 5-10 seconds
+* the screen goes dark and shows a partial (broken) Openmoko logo for about 5-10 seconds
-* the screen goes dark again, then shows the full OpenMoko logo
+* the screen goes dark again, then shows the full Openmoko logo
 * the machine will boot Linux now and start touch screen calibration
@@ Line 167: / Line 167: @@
 I know that it's almost industry practise to violate this part of the
-spec.  However, OpenMoko wants to set a good example and adhere to
+spec.  However, Openmoko wants to set a good example and adhere to
 standards :)

@@ Line 187: / Line 187: @@
 [[Category:Hardware ]]
-[[Category:Supported Phone| ]]
+[[Category:Hardware Support ]]
 [[Category:Neo1973 Hardware]]
 [[Category:Neo1973_Phase_0_related| ]]

@@ Line 182: / Line 182: @@
 you really want to use the charger for 500mA charging. see the kernel
 and u-boot pages in the wiki.
 [[Category:Neo1973_Phase_0_related]]

← Older revision		Revision as of 14:48, 13 July 2007
Line 182:		Line 182:
	you really want to use the charger for 500mA charging. see the kernel		you really want to use the charger for 500mA charging. see the kernel
	and u-boot pages in the wiki.		and u-boot pages in the wiki.
		+	[[Category:Neo1973_Phase_0_related]]

@@ Line 173: / Line 173: @@
 GTA01Bv4 and the new charger hardware contain circuit changes to address
 this problem in a usb spec compliant way.
 ==== Workaround ====