View source for Manuals/Neo FreeRunner/nl

From Openmoko

Jump to: navigation, search

You do not have permission to edit this page, for the following reasons:

  • The action you have requested is limited to users in the group: Administrators.
  • You must confirm your email address before editing pages. Please set and validate your email address through your user preferences.

You can view and copy the source of this page:

Templates used on this page:

Return to Manuals/Neo FreeRunner/nl.

Personal tools

De Inhoud van het Pakket

In de doos
Circle2.gif Neo FreeRunner
Circle2.gif Stylus
Circle2.gif Batterij
Circle2.gif Lader
Circle2.gif USB Kabel
Circle2.gif microSD Kaart van 512MB


Maak kennis met de Neo FreeRunner

AUX knop en telefoon aansluiting (van links naar rechts)
Aan/Uit knop, USB en externe GPS Antenne (van links naar rechts)
Achterkant met de batterij
De SIM kaart en de SD kaart horen hier
open de Freerunner langs hier
Open

Het installeren van de Micro-SD kaart, de SIM kaart, en de batterij

  1. Verwijder de achterkant als volgt : houd de Neo FreeRunner op zijn zij en gebruik uw vinger om de achterkant los te maken bij het slotje aan de bovenkant.
  2. Nu zie je de gecombineerde SIM en Micro-SD kaart houder onderaan het batterij compartiment.
  3. Maak de SIM kaart houder vrij door het metalen clipje naar beneden te doen, in de richting van de USB aansluiting. Gebruik daarvoor uw vingernagel. Wees wel voorzichtig, deze onderdelen zijn gevoelig en kunnen beschadigd raken door hen in de verkeerde richting te forceren.
  4. De de SIM kaart houder omhoog.
  5. The Micro-SD card holder is held in place by a latch on either side. It is easiest to open the Micro-SD card holder by releasing these latches one at a time rather than by lifting from the middle, as lifting from the middle tends to increase the latching pressure. A small screwdriver or knife can be used for this.
  6. Insert the Micro-SD card into the Micro-SD card holder. Note that the electrical contacts should face down and towards the edge of the Neo Freerunner.
  7. Close the Micro-SD card holder, making sure that both latches are securely fastened.
  8. Insert the SIM card into the SIM card holder, taking care to slide inside the two metal tabs in the cover. Please note that the electrical contacts should face down and that the cut corner should be closest to the external GPS Antenna Socket.
  9. Close the SIM card holder and lock it by sliding the metal clip towards the external GPS Antenna Socket on the FreeRunner.
  10. Insert the battery into the battery compartment, aligning the electrical contacts on the battery with the electrical contacts in the battery compartment. Insert the side with the electrical contacts first.
  11. Replace the rear cover on the FreeRunner.

Turning on the Neo Freerunner

Charging the Neo Freerunner

When using the Neo Freerunner for the first time, you should charge the battery completely. The battery can be charged using the provided charger or from a powered USB port capable of providing 500mA worth of power. Most computers will be able to charge the FreeRunner without any problems.

Charging at 100mA takes 6-12 hours and at 500mA takes 1-2 hours. (from openmoko.togaware.com)

You can boot your Neo FreeRunner in the following ways:

Circle2.gif You can power it up into an Openmoko image directly.
Circle2.gif You can boot it into U-Boot via NAND Flash.
Circle2.gif You can boot it into U-Boot via NOR Flash.

Booting the device into NAND and NOR Flash allows you to update the kernel and root filesystem.

Opstarten met de Openmoko Image

Menu2.jpg

Houd de Aan/Uit knop minstens 8 seconden ingedrukt, tot je het Opnmoko opstart scherm ziet. Dan kan je de Aan/Uit knop loslaten. De Neo FreeRunner start nu de Openmoko Image op.

Log into U-Boot in the NAND Flash

Menu7.jpg

Press and hold Power button, then press and hold AUX button for about 5 to 8 seconds. You should see the boot menu for the NAND Flash. Press the AUX button to select one of the options and then press the Power button to execute.

Log into U-Boot in the NOR Flash

Menu6.jpg

Press and hold the AUX button, then press and hold the Power button. Then, release the AUX button. You should see the boot menu for the NOR Flash. This option is usually used by developers or when flashing the FreeRunner. If you cannot log into U-Boot in NAND then you can log into U-Boot in the NOR Flash either.

NOTE: There are six options you can choose when you log into the NOR Flash.

1. Boot

2. Boot from MicroSD

3. Set console to USB

4. Set console to Serial

5. Reset

6. Power off



Schermbeveiliging unlocken

Wanneer het scherm is gelocked (schermbeveiliging, zie je een Matrix-style groene achtergrond met het Openmoko symbool onderin in het scherm met daarnaast een slotje aan de rechterkant. Sleep het Openmoko symbool naar de bovenkant van het scherm toe, of te wel naar het open slotje bovenin, en je scherm is unlocked.

Tools