View source for Manuals/Neo FreeRunner/nl

From Openmoko

Jump to: navigation, search

You do not have permission to edit this page, for the following reasons:

  • The action you have requested is limited to users in the group: Administrators.
  • You must confirm your email address before editing pages. Please set and validate your email address through your user preferences.

You can view and copy the source of this page:

Templates used on this page:

Return to Manuals/Neo FreeRunner/nl.

Personal tools

De Inhoud van het Pakket

In de doos
Circle2.gif Neo FreeRunner
Circle2.gif Stylus
Circle2.gif Batterij
Circle2.gif Lader
Circle2.gif USB Kabel
Circle2.gif microSD Kaart van 512MB

Maak kennis met de Neo FreeRunner

AUX knop and telefoon aansluiting (van links naar rechts)
Aan/Uit knop, USB en externe GPS Antenne (van links naar rechts)
Achterkant met de batterij
De SIM kaart en de SD kaart horen hier
open de Freerunner langs hier

Het installeren van de Micro-SD kaart, de SIM kaart, en de batterij

  1. Remove the rear cover of the Neo FreeRunner by first holding the Neo FreeRunner on the side and then use your fingernail to prise off the rear cover at the slot on top of the device.
  2. Now you should be able to locate the combined SIM and Micro-SD card holder at the bottom of the battery compartment.
  3. Unlock the SIM card holder by sliding the metal clip down, towards the USB socket, with your fingernail. Use caution, as these parts are delicate and could be damaged by forcing them in the wrong direction.
  4. Lift up on the SIM card holder.
  5. The Micro-SD card holder is held in place by a latch on either side. It is easiest to open the Micro-SD card holder by releasing these latches one at a time rather than by lifting from the middle, as lifting from the middle tends to increase the latching pressure. A small screwdriver or knife can be used for this.
  6. Insert the Micro-SD card into the Micro-SD card holder. Note that the electrical contacts should face down and towards the edge of the Neo Freerunner.
  7. Close the Micro-SD card holder, making sure that both latches are securely fastened.
  8. Insert the SIM card into the SIM card holder, taking care to slide inside the two metal tabs in the cover. Please note that the electrical contacts should face down and that the cut corner should be closest to the external GPS Antenna Socket.
  9. Close the SIM card holder and lock it by sliding the metal clip towards the external GPS Antenna Socket on the FreeRunner.
  10. Insert the battery into the battery compartment, aligning the electrical contacts on the battery with the electrical contacts in the battery compartment. Insert the side with the electrical contacts first.
  11. Replace the rear cover on the FreeRunner.

Turning on the Neo Freerunner

Charging the Neo Freerunner

When using the Neo Freerunner for the first time, you should charge the battery completely. The battery can be charged using the provided charger or from a powered USB port capable of providing 500mA worth of power. Most computers will be able to charge the FreeRunner without any problems.

Charging at 100mA takes 6-12 hours and at 500mA takes 1-2 hours. (from

You can boot your Neo FreeRunner in the following ways:

Circle2.gif You can power it up into an Openmoko image directly.
Circle2.gif You can boot it into U-Boot via NAND Flash.
Circle2.gif You can boot it into U-Boot via NOR Flash.

Booting the device into NAND and NOR Flash allows you to update the kernel and root filesystem.

Start the Openmoko Image


Press and hold Power button for about 8 seconds, until the Openmoko splash screen turns up. You may now release the Power button and the Neo FreeRunner will continue to boot into the Openmoko Image.

Log into U-Boot in the NAND Flash


Press and hold Power button, then press and hold AUX button for about 5 to 8 seconds. You should see the boot menu for the NAND Flash. Press the AUX button to select one of the options and then press the Power button to execute.

Log into U-Boot in the NOR Flash


Press and hold the AUX button, then press and hold the Power button. Then, release the AUX button. You should see the boot menu for the NOR Flash. This option is usually used by developers or when flashing the FreeRunner. If you cannot log into U-Boot in NAND then you can log into U-Boot in the NOR Flash either.

NOTE: There are six options you can choose when you log into the NOR Flash.

1. Boot

2. Boot from MicroSD

3. Set console to USB

4. Set console to Serial

5. Reset

6. Power off

Unlocking the screen

When the screen is locked, you should see a Matrix-style green graphic with the Openmoko symbol in the middle of the bottom of the screen along with lock and unlock symbols. If you drag the Openmoko symbol to the unlock symbol at the top then the screen will become unlocked.