Christian did some stracing on TomTom device, and result is great logs at http://www.maintech.de/download/hammerhead-strace.log . 'pH5' on IRC has put up some traces at http://linuxtogo.org/~ph5/tmp/gllin (a cold start, a hot start and a somewhat longer trace). He even has a software that can init and send command to phase-1 openmoko device in http://linuxtogo.org/~ph5/tmp/hhtest.c . (Plesae use strace -s9999 -x to produce traces).
GPS signals at wikipedia seems to be required reading for very basics, along with this page from University of Colorado for more in depth stuff.
http://home.earthlink.net/~cwkelley/ has sources for open-source GPS receiver, and
http://home.earthlink.net/~cwkelley/documentation.htm is its documentation.
GP2021 is "dumb" GPS receiver, similar to hammerhead. (But I think it communicates over ISA bus, not over serial). However, its data sheets are freely available. Well, hammerhead marketing tells us that their GPS chip is something special, http://www.gpsworld.com/gpsworld/article/articleDetail.jsp?id=3053 . It seems to differ from "dumb" receivers by doing code phase search in hardware, directly.
Possible lock scheme that it may use
From reading the published brief information sheets on global locates products, not the patents.
The global locate chip has massively parallel correlators, and configurable integrators to integrate over a given time.
I would expect it to do something like - in this case.
- Load orbit data from file.
- Look at time.
- Compute which satellites are up.
- Init the GPS.
- Set the hardware to expect to receive from the set of visible satellites (the hardware is unlikely to be designed to receive them all at once, as you'll never see more than around 12 of the nominal 24).
- Set the integration time at 10ms-20ms or so - around, or a bit under a data bit.
- Now, read back the outputs of the integrators, to see if we've got possible data.
- If we do have data, spend a bit of time working out the exact relative phase of the PRN with regard to the carrier - each 'chip' of the PRN is around a thousand cycles of the carrier - you need to work this out exactly to get psuedoranges with a resolution of under a meter.
- it's possible this is done in hardware
- Now that we've got all the satellites locked in the hardware, simply interrogate the hardware regularly, so that we can read out the 50bps datastream from each satellite.
- It seems this step takes 19s or so. From the first timestamp in the file, to the first GPGSV line - satellites in view, and their actual signal strengths.
- Read the navigation messages from each satellite, which cycles every 6 seconds.
- Compute a position.
- Output it to NMEA
- It seems this takes 22 seconds.
To keep to the datasheet of 1s position times, it cannot read the whole navigation message, but significantly under 50 bits of it.
- Use 'AGPS' data to initialise the hardware to a condition where it can get a rapid lock - perhaps telling it the Doppler - then compute what the navigation message from each satellite may be, based on the internal clock.
- Work out at what point in this navigation message the 20-30 bits that it's received come.
- Compute the time that was in the navigation message, though it may not have picked it up (from the internal clock) and add it to the information on where the bit edges are from the hardware.
- If the uncertainty in relative time - due to local clock drift and movement of the GPS device - is under 10ms, then you know immediately as you detect the satellite signal the current satellite time - you simply snap the time to the nearest bit-edge, letting you immediately compute a position, without waiting for more data.
- With typical crystal accuracy, this implies you need to take a position every 3 minutes or so in order to keep the clock set correctly enough for this to work.
- This gives you a psuedorange to the satellite to within several meters.
- Compute a position.
Looks like there were 8 satellites overhead at the time that log was made.
The protocol appears to be oriented around 32-bit words (the single-byte markers notwithstanding.) LSB-first, as can be seen on negative numbers.
The first stream of 0x80's to the GPS is simply to synch up the UART in the GPS to the correct baudrate.
Packet format (same format in both directions):
- The start of a packet is marked by FF or FE.
- FF in packets that do not carry data, but rather explicitly request a response. (This isn't used very often. More often we receive data without explicitly requesting it.) The response will be an FE-packet with the same length and type as the FF-packet. The GPS does not send any FF packets, only gltt does.
- FE in packets that carry data sections.
- The first word (32 bits) following the start-of-packet marker is the header.
- The first byte (if it's indeed little-endian, the least significant byte) gives the data length, measured as the number of data words minus 1. For FE-packets, this is the length of the data section of this packet. For FF-packets, it's the length of the data section in the expected response.
- The second byte of the header is always FD.
- MS nibble of the third byte might be flags for the packet.
- 0x4 set: The words are for increasing register numbers
- 0x4 not set: The words are for/from the same register. The register is probably something like a FIFO
- LS nibble of the third byte is an identifying number of the channel (1-8), 0 in case this is not channel-specific
- The fourth byte is the packet type. It seems to be more like a register (start) number.
- In FE-packets only, the data section (n 32-bit words) follows.
- Finally, FC is sent to mark the end of the packet.
- After the FC in an FF-packet, gltt sends a bunch of zeros. In some cases it sends a number of zeros equal to the number of bytes in the response packet; in some cases it sends more. I would guess that these have no effect.
ff 04fdc00c fc
(possibly followed by zeros), is a request for a packet of type 0C, with length 20d ((4 + 1) * 4), and flags C0.
fe 04fdc00c 0025102a 45dbdd4e 36030000 4b260000 16010000 fc
would be an appropriate response.
(Ugh, I do not understand this. Is it SEND or RECEIVED packets? Pavel 22:26, 6 May 2007 (CEST))
|| Max length
|| Min length
All packets in this category have the "channel" (or "ID") field set to 0.
SEND Packet 04
Flags = 4
In cold2.log this packet comes only once at the start.
Part of this packet seems to setup the timestamp clock (see packet 16).
92 24 11 02 7b 39 8e 23 00 00 00 00 7b 39 8e 23
Word 2 and 4 (both are 0x238e397b = 596523387) seem to control the timestamp clock. Multipliying this value by say 0.99 makes the timestamp clock run at 0.99 its normal speed. So this value is some sort of "frequency".
SEND Register/Packet 08
One 32 bit word bitmask
- 0x2000 lets the timstamp clock (See 16) run. One can start and and it using this bit
- 0x4 resets the timestamp clock to 0. (putting a 0x4 will reset the clock. The bit is self-resetting to 0.
RECEIVED Packet 0c
Flags = 0
Is global -- not about particular sattelite, probably fixed length and rare.
RECEIVED Packet 16
Flags = 8;
Comes only after request for it.
The chip seems to have an internal 1ms clock. This returns the counter for this clock.
It seems, that the clock can be widely tuned (probably using divider or so): At least I saw 1000 ticks and 2000 ticks per second.
CMD-04 and CMd-08 seem to be needed to init and start it.
Satelite / channel specific packets
SEND Packet 00
Packet type 00 (with the exception of the very first FE-packet in the log) appears to specify a particular satellite to track. It also seems that this specifies the "ID" field (LS nibble of the third header byte) that will be used for future packets concerning this satellite. (Non-satellite-specific packets have ID=0.)
Bits 3-7 of the 11th byte of the packet -- third byte of the third data word -- are the satellite PRN number. In this log only 8 satellites appear to be tracked (2, 4, 8, 10, 13, 23, 27, 29). If I'm reading the GPGSV messages correctly, 24 should also be visible, but it doesn't appear gltt even attempts to track it.
As for the rest of the packet... There's a lot that gets repeated, information common to all the satellites, at least initially. When a batch of 8 of these packets gets sent, usually only the PRN and two other words differ among the 8. So those two words contain whatever satellite-specific info is needed, it seems. They both appear to be little-endian integers, one around -10^8 and one around 10^8.
(Info needed to search for sattelite... doppler frequency range and phase range is useful).
RECEIVED Packet 10
Last four bytes are the little endian timestamp, in miliseconds. (Ok, it may actually be number of frames or something on that particular channel).
Packet length is constant (always 16 bytes.)
RECEIVED Packet 23
It carries variable-length array of 16-bit integers... 6 to 32 entries were seen.
RECEIVED Packet 06, 08
short packets, 06 has varying length, and both are rare.
RECEIVED Packet 9d
Okay, so packets 10, 23 and 9d come in groups, for each sattelite, and they seem to contain enough info to compute position. (9d seems to come later than the other two, perhaps only after sending a packet 08?)
Packet 9d seems to contain 2 32-bit integers (second one is signed), then 3, 0, 0 and flags (?) -- so the packet length is constant.
RECEIVED Packet 0e
Always appears to be 24 bytes. Satellite-specific.
RECEIVED Packet 9e
Always appears to be 8 bytes. Satellite-specific. First 4 bytes are a signed 32-bit integer.
RECEIVED Packet 9f
Comes in variants of differing lengths: 20, 36, and 84-byte packets were seen. Satellite-specific.
It is possible to translate NMEA messages into something readable using script from http://atrey.karlin.mff.cuni.cz/~pavel/outgoing/hhdecode , and using c decoder http://atrey.karlin.mff.cuni.cz/~pavel/outgoing/hh.c .
NMEA description is available at http://www.gpsinformation.org/dale/nmea.htm .
At this point:
256 write(GPS, "\xfe\x00\xfd\x40\x08\x40\x60\x00\x00\xfc", 10) = 10
256 write(GPS, "\xfe\x00\xfd\x40\x08\x40\x60\x00\x00\xfc", 10) = 10
256 write(NMEA, "\x24\x47\x50\x47\x47\x41\x2c\x31\x35\x34\x31\x30\x34\x2e\x39\x35\x2c\x34\x39\x34\x38\x2e\x39\x35\x30\x33\x33\x39\x2c\x4e\x2c\x30\x30\x39\x35\x37\x2e\x39\x35\x35\x39\x37\x39\x2c\x45\x2c\x31\x2c\x30\x36\x2c\x35\x2e\x30\x2c\x32\x32\x30\x2e\x30\x2c\x4d\x2c\x2d\x30\x2e\x35\x38\x31\x30\x31\x34\x2c\x4d\x2c\x2d\x30\x2e\x31\x39\x30\x30\x31\x39\x30\x2c\x2a\x34\x30\x0d\x0a", 91) = 91
256 write(NMEA, "$GPGGA,154104.95,4948.950339,N,00957.955979,E,1,06,5.0,220.0,M,-0.581014,M,-0.1900190,*40
", 91) = 91
...6 satelitte GPS fix was obtained. (And yes, there's big read few lines before that in the log).
GSA sentence looks interesting, too. It tells us satellites #02, #04, #08, #10, #13 and #27 were used at this point.
256 write(NMEA, "\x24\x47\x50\x47\x53\x41\x2c\x41\x2c\x33\x2c\x30\x32\x2c\x30\x34\x2c\x30\x38\x2c\x31\x30\x2c\x31\x33\x2c\x32\x37\x2c\x2c\x2c\x2c\x2c\x2c\x2c\x36\x2e\x37\x2c\x33\x2e\x30\x2c\x36\x2e\x30\x2a\x33\x45\x0d\x0a", 51) = 51
256 write(NMEA, "$GPGSA,A,3,02,04,08,10,13,27,,,,,,,6.7,3.0,6.0*3E
The whole log is