Gpsd - Revision history

Glenn: +link

2009-07-25T06:21:25Z

+link

2009-07-18T10:49:56Z

+cat

2009-07-18T10:48:52Z

‎GPS on GTA02: clarify

2008-09-24T08:11:45Z

Warning about ogpsd incompatiblity

2008-08-31T12:37:59Z

Replacing 'Freerunner' with 'FreeRunner'

2008-08-21T13:55:07Z

‎GPS on GTA02

2008-07-13T09:04:55Z

‎Q: Can I get NMEA data from the GPS?

2008-07-09T09:40:25Z

2008-07-03T17:20:35Z

2008-06-09T20:05:56Z

‎Q: Can I get NMEA data from the GPS?

← Older revision		Revision as of 06:21, 25 July 2009
Line 1:		Line 1:
−	{{Warning\|The gpsd has been obsoleted by the ogpsd which offers a DBUS interface. Do not run these two daemons side by side. If backward compatibility is needed, use ogpsd with fso-gpsd.}}	+	{{Warning\|The gpsd has been obsoleted by the [[ogpsd]] which offers a DBUS interface. Do not run these two daemons side by side. If backward compatibility is needed, use ogpsd with fso-gpsd.}}

	== What is GPS ==		== What is GPS ==

@@ Line 74: / Line 74: @@
 == GPS on GTA02 ==
-To get gpsd working on the Neo FreeRunner you have to run the following commands:
+:''On [[Om 2009]] use [[ogpsd]]''
   echo "GPS_DEV=\"/dev/ttySAC1\"" > /etc/default/gpsd

← Older revision		Revision as of 08:11, 24 September 2008
Line 1:		Line 1:
		+	{{Warning\|The gpsd has been obsoleted by the ogpsd which offers a DBUS interface. Do not run these two daemons side by side. If backward compatibility is needed, use ogpsd with fso-gpsd.}}
		+
	== What is GPS ==		== What is GPS ==

@@ Line 72: / Line 72: @@
 == GPS on GTA02 ==
-To get gpsd working on the Neo Freerunner you have to run the following commands:
+To get gpsd working on the Neo FreeRunner you have to run the following commands:
   echo "GPS_DEV=\"/dev/ttySAC1\"" > /etc/default/gpsd

@@ Line 96: / Line 96: @@
 * The gpsd program 'gpspipe', with the -r switch will output NMEA data with the current position information. The right way to do it is to use libgpsd in your program if possible.
 * [[Gllin]] writes its NMEA data to the pipe by default, see [[getting GPS console output with gllin]] for more.
 {{Languages|Gpsd}}
 [[Category:GPS]]

@@ Line 72: / Line 72: @@
 == GPS on GTA02 ==
-To get gpsd working on the Neo Freerunner you have to edit /etc/default/gpsd change GPS_DEV="/dev/ttyS3" to GPS_DEV="/dev/ttySAC1". that's it
+To get gpsd working on the Neo Freerunner you have to edit /etc/default/gpsd, change GPS_DEV="/dev/ttyS3" to GPS_DEV="/dev/ttySAC1". that's it
 == Q & A ==

← Older revision		Revision as of 17:20, 3 July 2008
Line 69:		Line 69:

	On the GTA01, the Hammerhead are configured that connected with the host processor through the UART. The UART of data output/input is connected to the UART 1 of the SC2410. The UART of the hardware flow control is connected to the UART 2 of the SC2410.		On the GTA01, the Hammerhead are configured that connected with the host processor through the UART. The UART of data output/input is connected to the UART 1 of the SC2410. The UART of the hardware flow control is connected to the UART 2 of the SC2410.
		+
		+	== GPS on GTA02 ==
		+
		+	To get gpsd working on the Neo Freerunner you have to edit /etc/default/gpsd change GPS_DEV="/dev/ttyS3" to GPS_DEV="/dev/ttySAC1". that's it

	== Q & A ==		== Q & A ==

@@ Line 89: / Line 89: @@
 ====Q: Can I get NMEA data from the GPS?====
-A: Not directly. However, the gpsd program 'gpspipe', with the -r switch will output NMEA data with the current position information. The right way to do it is to use libgpsd in your program if possible.
+A:
 {{Languages|Gpsd}}
 [[Category:GPS]]