Getting Started with your Neo FreeRunner
m (Small typo: loosing != losing)
|Line 335:||Line 335:|
After the ssh connection and login in again via ssh reconnect to the running screen session with:
Revision as of 20:42, 25 April 2009
English • العربية • Български • Česky • Dansk • Deutsch • Esperanto • Eesti • Español • فارسی • Suomi • Français • עברית • Magyar • Italiano • 한국어 • Nederlands • Norsk (bokmål) • Polski • Português • Română • Русский • Svenska • Slovenčina • Українська • 中文(中国大陆) • 中文(台灣) • Euskara • Català
Thank you for purchasing this Developer release of Neo FreeRunner. The Neo FreeRunner phone is the second hardware platform to take advantage of Openmoko. This guide will help you get to know your Neo FreeRunner and how to start using your Neo FreeRunner.
Some Frequently Asked Questions for new owners are featured in the FAQ.
- Neo FreeRunner
- USB Cable (A -> Mini-B 5-pole)
- Thank You green card
Get the source code
The software included in this product contains copyrighted software that is licensed under the GPL. A complete corresponding source code or CD-ROM ISO image with the GPL license is available for download here. You may also obtain the same corresponding CD-ROM by sending a money order or check for $10 to any one of our distributors.
Please write “source for Neo FreeRunner ” in the memo line of your payment.
Setting up the hardware, getting to know the Neo FreeRunner physically
Installing the Micro-SD card, the SIM card, and the Battery
Remove the rear cover of the Neo FreeRunner by first holding the Neo FreeRunner on the side and then use a credit card (or your fingernail, if you have strong fingernails) to prise off the rear cover at the slot on top of the device.
Unlock the SIM card holder by sliding the metal clip down, towards the USB socket, with your fingernail. Use caution, as these parts are delicate and could be damaged by forcing them in the wrong direction.
The Micro-SD card holder is held in place by a latch on either side. It is easiest to open the Micro-SD card holder by releasing these latches one at a time rather than by lifting from the middle, as lifting from the middle tends to increase the latching pressure. A small screwdriver or knife can be used for this.
Insert the Micro-SD card into the Micro-SD card holder. Note that on the inside of metal part of the holder there are little holding tabs for the card. Slide the card in these holders (on the metal part) before closing the card holder. Note that the electrical contacts should face down and towards the edge of the Neo FreeRunner.
Insert the SIM card into the SIM card holder, taking care to slide inside the two metal tabs in the cover. Note that the electrical contacts should face down and that the cut corner should be closest to the external GPS Antenna Socket.
Insert the battery into the battery compartment, aligning the electrical contacts on the battery with the electrical contacts in the battery compartment. Insert the side with the electrical contacts first.
A short video is also available. It was shot using the previous version of the Neo, but the installation procedure remains the same.
Charging the Neo FreeRunner
Before using the Neo FreeRunner for the first time, you should charge the battery completely. The battery can be charged using the provided charger at 1000mA or from a powered USB port capable of providing 500mA worth of current. Most computers will be able to charge the FreeRunner without any problems.
Neo FreeRunner does NOT charge when powered off, so be sure to turn it on and allow it to boot all the way to the GUI (Graphical User Interface). This should happen automatically when you plug in USB power, either from a computer or the provided charger.
Although the provided charger is rated at 2A, the maximum charge rate of the Neo FreeRunner is 1A, and thus the charge rate with the charger is less than the charger capacity.
The provided charger includes three "national" plugs. The default is North America, with alternative U.K (3 square pins) and Euro (two round pins) adapters. To install the alternative power adapters, depress the latch in the cover (on the opposite side of the charger from the product information label) and slide the cover outward. Note that the two North American pins do not come out; the other adapters slide over them, and snap into place. The two-pin Euro adapter is removed in the same way as the cover. The three-pin U.K. adapter is removed by gently pressing the dummy ground pin (black) toward the end of the adapter with the cord and then sliding it off the adapter.
Charging an empty battery at 100mA takes 12~15 hours, at 500mA takes 2,5~3,5 hours, and at 1000mA takes 1.5~2.5 hours. (90%~100%) [to be confirmed]
|NOTE: See Neo FreeRunner Hardware Issues about not allowing the battery to discharge completely.|
Buttons and connectors
Tapping the power button exits the current application.
Holding the power button brings up a menu allowing you to:
Tapping the Aux button hides or shows the currently running application.
Holding the Aux button brings up a menu allowing you to:
Booting the Neo FreeRunner takes about 2 minutes overall, so patience is in order. The longest step comes after the Linux boot messages in very small fonts have scrolled by, at the graphical "openmoko" sunrise page.
The phone jack is a 2.5mm connector with four contacts: stereo + MIC. It is compatible with the headsets used by Motorola smartphones (A780,A1200, ...) and the V-360.
More information on Headset page.
Unlocking the screen
When the screen is locked, you should see a Matrix-style green graphic with the Openmoko symbol in the middle of the bottom of the screen along with lock and unlock symbols. If you drag the Openmoko symbol to the unlock symbol at the top then the screen will become unlocked.
Identifying which revision you have
You will want to determine which revision of the phone you have
- remember your date code, the bottom of your shipping box should have a sticker stating it.
- read Finding_hardware_revision
Because the software changes so rapidly and the phones were imaged during mass production, we don't ship the newest image with phones. There are two different kinds of images shipped with the phones:
1. Om 2007.2
2. Om 2008.9
But according to the FAQ and Distributions pages, all phones ship with Om 2007.2. This distribution is no longer supported, so before even getting your feet wet, you'll probably want to switch to something else, especially since the FreeRunner is not really usable as a mobile phone with these old distributions.
Switching to another distribution is easy if you have a computer with a USB port and internet connectivity that can run the dfu-util utility. Most current Linux distros have packaged dfu-util, so if you use Linux you can probably just get it from your distro's repository. The next step is to choose which Openmoko distribution to switch to. See Distributions for information about the alternatives.
That page will point you to the files to download, and to the instructions for installing them using dfu-util.
For Om 2007.2
See Today/2007.2 for more information about the Today page and customization.
Launch Task Page
|Stub: This is a stub. You can help OpenMokoWiki by expanding it.|
Running Tasks Page
|Stub: This is a stub. You can help OpenMokoWiki by expanding it.|
Exiting from and switching to an Application
Any time an application is running, you can simply click the device's power button and the application will exit, returning you to the Today page.
Alternatively, you can cycle through active applications using the AUX button
Clicking the top-left of the screen displays the drop down task menu. This menu lists all active applications and allows to switch directly to any one. Note: If the task menu is not shown, click and hold the Aux button to bring up the Aux menu, and select "Toggle Fullscreen".
Using the terminal
To start a console from "Today" page, click the middle tab at the bottom of the screen to display the "Launch applications" page, then select Terminal in the "Applications" submenu. The multitaps keyboard slides up (and down) from the bottom of the screen automatically when you touch the screen.
Setting date and time
From the terminal, type the following, but replace MM with the month (01-12); DD with the day (01-31); hhmm with the time (0000-2359); YYYY with the year (optional); and .ss with the seconds (optional).
date -s MMDDhhmmYYYY.ss
To make the change persist between reboots, sync the hardware clock with the updated system time.
See Setting Date and Time for more discussion, including synchronizing with an NTP server.
Note: UNIX traditionally sets the system clock to GMT (UTC) or "Zulu" (Z time zone). So I use the stanza:
date -u MMDDhhmmYYYY.ss (well, I usually ignore the seconds)
Then I can set the local time using the techniques described elsewhere. iceworm
Accessing the microSD card
Mounted at /media/card by default.
If you have multiple partitions on the card, the first (/dev/mmcblk0p1) will be mounted at /media/card, the second at /media/mmcblk0p2, the third at /media/mmcblk0p3 etc. To setup the package management to write on the microSD card when installing new software follow the package management guide.
fox example :
Filesystem 1k-blocks Used Available Use% Mounted on rootfs 252544 153560 98984 61% / /dev/root 252544 153560 98984 61% / /dev/root 252544 153560 98984 61% /dev/.static/dev udev 2048 76 1972 4% /dev /dev/mmcblk0p1 3362 1794 1568 53% /media/card /dev/mmcblk0p2 476382 157368 294419 35% /media/mmcblk0p2 tmpfs 61928 380 61548 1% /var/volatile tmpfs 61928 0 61928 0% /dev/shm
For Om 2008.12
Entering the SIM PIN
Some SIM cards require a PIN code to be entered. If your SIM card is like this, you will see a screen like this after the FreeRunner boots:
The keypad in the lower part of the screen shows only letters, and your PIN is probably numeric. Switch to other keypads by stroking downwards on the screen with the stylus. Then enter your PIN. If you enter a wrong digit, you can backspace by stroking the screen to the left with the stylus. (Keep trying if it doesn't seem to work.) Finally, having composed the correct PIN, tap on the composed number with the stylus. This will enter it into the dialog box where it needs to be. After a brief pause, you will then see the word "Enter" at the top right of the keypad. Tap it. The PIN will then be checked, and if all is well, the Home Screen (next section) will be displayed.
The Home screen
With the bare-bones installation, the home screen looks like this.
In Om 2008.12, no terminal app is installed by default. To get to a command prompt, you need to set up USB-based networking and use SSH; see next section. Before trying to ssh into the FreeRunner, go into the Settings app and set "Suspend" to "off". The default is to go into suspend mode after 30 seconds without activity on the touchscreen, and when in suspend mode, the FreeRunner does not respond to commands sent over the ssh session.
Set up USB-based networking, SSH and update
Openmoko allows TCP/IP-over-USB networking for your phone. The main advantages of this are
- You don't need to set-up GPRS or WLAN network connection for the phone software to reach the Internet
- You can SSH from your computer into the phone shell and comfortably do low-level tasks using your computer's terminal software and real keyboard instead of the tiny screen and touchscreen keyboard
Naturally, the phone must be connected to your computer with USB cable.
Connect with the Neo FreeRunner
This is discussed in the USB Networking section.
Update with the package manager
In order to keep the FreeRunner up-to-date with the latest features and bug-fixes, it is advisable update the software at regular intervals.
There are two main methods of doing this:
- upgrading with the package manager Opkg
- or manually flashing the device (see Flashing the Neo FreeRunner).
There are three layers to the software on the FreeRunner:
- uBoot: Think of u-boot as a combination of the BIOS and Grub on a PC.
- Kernel: The Linux kernel
- Root Filesystem: The rest of the system
Note that uboot, the kernel and the root filesystem may all be flashed to update them. For uboot, this is the only possibility (see Flashing_the_Neo_FreeRunner#Flashing_the_boot_loader). The advantage of flashing the kernel manually rather than using opkg seems to be speed. The disadvantage of flashing the root file system is that it wipes out all local modifications, including /home. If /home is moved to the SD disk, this is no longer a problem.
| WARNING: UPGRADING TO DAILY KERNELS FROM THE DEVELOPMENT BRANCH MAY BREAK THINGS. That said, assuming that your FreeRunner can access the internet (see above), the kernel and other packages can be updated with
The first updates the repository information, telling opkg what packages are available. The second allows you to see what the package manager wants to do. The third upgrades all packages for which a newer version is available. At the moment, some signature files are missing (404 errors), which opkg complains about, but this is cosmetic. The repositories will still update with the missing signature files.
Important: If you have followed the Getting Started Guide this far, but opkg upgrades do not appear to be happening. Try checking the .conf files in the /etc/opkg/ directory. If you see four URLs pointing at http://buildhost.openmoko.org/, this is your problem. http://buildhost.openmoko.org/ is no longer supported. If you're running Om 2007.2 (the stock distribution that comes with the Freerunner according to the FAQ), you'll need to edit those files to point to an unofficial User Repository. Or, you could install another distribution (which is probably the best bet in the long run).
Note that running opkg upgrade on a factory-fresh phone will upgrade dropbear (the ssh software) and various xserver packages, and neither upgrades elegantly while in use. Xserver must be updated over ssh to complete succesfully. Dropbear can be updated over ssh with the proper command:
nohup opkg upgrade dropbear &
Or upgrade it directly in the FreeRunner terminal.
opkg upgrade dropbear
When updating over ssh, the session will be interrupted, but the command should complete successfully(check nohup.out on your device to verify), and you should be able to reconnect within a few seconds.
Another (better) option is to start a screen session before the upgrade with:
After losing the ssh connection and login in again via ssh reconnect to the running screen session with:
Then connect to the FreeRunner via ssh and type:
And run this command :
Alternatively you can upgrade the xserver packages via ssh and then upgrade the rest from the FreeRunner's terminal.
If you do your first upgrade in two installments like this, it will go more smoothly.
It will be possible in the future to update uboot with opkg, but this has not yet been implemented.
There are many applications you can install - check out the Repositories for a list of packages, an example of how to add a repository using scaredy cat as an example can also be found here. A list of pre-installed and available packages with descriptions can be found here - Available Packages. Or you can check Applications page to get applications developed from community.
If you want to install any application on Neo, there three steps:
1. Download the applicatiion you want to install on Neo.
2. scp the opkg/ipk file to the root of Neo.
3. Use Opkg command to intall opkg files.
By following example you can install web browser on Neo:
The calendar can be installed with
First download and unpack it on your GNU/Linux host:
wget http://www.ginguppin.de/files/minimo.tar.bz2 tar jvxf minimo.tar.bz2
Copy it over to the FreeRunner:
scp minimo_* firstname.lastname@example.org:/tmp
Then on the FreeRunner:
opkg install /tmp/minimo_0.02\+cvs20070626-r0_armv4t.ipk
If you can export your contacts to VCard format, either multiple files or single file containing all of them, you may use the script on Import Vcf Contacts page to bring them to Neo.
The next steps
Congratulations for setting up your Neo FreeRunner. There are many more resources to help free your phone:
Customize the interface
home screen clock, keyboard
The stock Openmoko2007.2 image flashed onto the Neo FreeRunner is really just the bare bones. For example, you don't have the clock and the quick-launch icons showing. Here's how you can change that:
- dbus-launch gconftool-2 -t boolean -s /desktop/poky/interface/reduced false
- /etc/init.d/xserver-nodm restart
If you rather have a regular clock instead of the digital one, do this instead:
- dbus-launch gconftool-2 -t boolean -s /desktop/poky/interface/reduced false
- dbus-launch gconftool-2 -t boolean -s /desktop/poky/interface/digital_clock false
- /etc/init.d/xserver-nodm restart
REMOVE CLICK SOUND VIA /etc/pulse/session
More information about today screen customization at Today/2007.2.
Also, if you prefer having a full keyboard, using matchbox's qwerty keybord, see these instructions. Then you may also see these, which describe a way to add an applet allowing the showing/hiding of that keyboard.
Use the GPS
Play with WLAN, GPRS and Bluetooth
There are plenty of development opportunities to integrate these functions in the Openmoko software.
WLAN: See Wireless Networking
GPRS: See Manually using GPRS
Bluetooth: See Manually using Bluetooth
Testing a new distribution
For the feature of Openness, you can flash any Linux Distributions into FreeRunner. You can testing a new distribution by following ways:
- Booting from SD.
- Boot from the built-in NAND flash memory.
Welcome to the community
The release of the FreeRunner in the summer 2008 has led the community into a new period of rapid growth. The resources available are summarized on the Community Resources. These are always exciting and interesting times to live in when the balance between Chaos and Order tilts towards change.
As an entry point, the openmoko community mailing list is perhaps the most active. As of July 2008, its volume amounts to dozens of messages per day. Read the Community_Updates for a digest. Openmoko people are there too. You may ask for help on the [support mailing list].
Or if you use IRC, there is always a good group in the channel #openmoko on FreeNode.
The links on the top-right of this page lead to the sister sites in the Openmoko community:
- Home and Wiki lead to the same Main Page on the wiki. It needs cleaning, we know...
- Doc leads to the bug Tracking system.
- Planet goes to the collection of Openmoko-relatd blogs.
- Projects is the GForge, free hosting for application developers.
- Lists is the listing of all the public mailing lists on lists.openmoko.org.
- Neo FreeRunner. The top-level view of the specifications.
- Neo FreeRunner GTA02 Hardware. The detailed specifications.
- GTA02 Openness. Ultimate chip-level specifications, data sheets and hardware documentation.
- Distributions. Strengths and weaknesses of the various distributions available for the Neo.
- FAQ#Getting_Started_with_your_Neo_FreeRunner. Answers.
To search this wiki with Google, use the following search term:
<search term> site:http://wiki.openmoko.org/wiki/