Freerunner Navigation Board

From Openmoko

(Difference between revisions)
Jump to: navigation, search
m
m
Line 36: Line 36:
 
Except for the above mentioned sensors there have been written plugins for:
 
Except for the above mentioned sensors there have been written plugins for:
 
* [http://www.st.com/stonline/products/literature/ds/12726/lis302dl.htm LIS302DL] accelerometers (the ones included in our devices)
 
* [http://www.st.com/stonline/products/literature/ds/12726/lis302dl.htm LIS302DL] accelerometers (the ones included in our devices)
* BMP085 pressure sensor
+
* [http://wiki.openmoko.org/wiki/I2C_Pressure_Sensor BMP085] pressure sensor
  
 
This is a screenshot of application monitoring the X and Y gyro-axis of the navigation board as well as the X-axis of the digital compass:
 
This is a screenshot of application monitoring the X and Y gyro-axis of the navigation board as well as the X-axis of the digital compass:

Revision as of 18:45, 30 April 2010

Preliminary Information. This page will be moved as soon as it contains the most important imformation about the board. (probably this weekend).

Contents

Freerunner Navigation Board

The Freerunner Navigation Board is a small PCB which can be mounted inside the case to extend the Freerunner with additional Hardware. The Board contains the triaxial digital compass chip HMC5843 from Honeywell and two gyroscope chips from InvenSense (IDG650, ISZ650) to provide a triaxial gyroscope solution.

Full schematics and layout files are available from chonyota.net/freerunner

Hardware details

The board can be connected to the I2C bus which is available on testpads around the debug connector.

The compass chip is directly connected to the I2C bus. The gyroscopes have an analog output which is digitized using a 16-bit A/D converter ADS1115 from Texas Instruments.

Additional features which were planned but are not implemented yet: The board contains the footprint to add an additional MSP430 microcontroller from TI. It would be used to control the offset compensation features of the gyroscopes, read their internal temperature sensors and switch them off when not used. Latter can actually be done using a GPIO line which is available at a testpoint H-TP1516.

Software support

Right now, this additional hardware is not supported out of the box, but there are some pieces of software available to demonstrate that the hardware actually works.

Drivers

Hardware drivers are available from gitorious.

Digital compass

A kernel driver is available to control the HMC5843 digital compass through sysfs entries. Vala hackers can use a vala library for easier access.

Gyroscope

The Gyroscopes need a driver for the ADCs which can be downloaded from the ADS1115 repository. Besides the kernel module, these chips can be accessed from userspace using the i2c-dev driver and a userspace library for easier access. Vala bindings are available.

End user software

A Vala-based sensor monitor developed by User:MicVM can be used to visualize the sensor values. The software is very experimental. You are using it at your own risk :)

The monitor has been developed in order to easily add arbitrary sensors as sources. The monitor uses GTK and Cairo for drawing the values and right now is quite slow on the GTA02. We are working on improving the refresh speed. Possibly with the same toolkit.

Except for the above mentioned sensors there have been written plugins for:

  • LIS302DL accelerometers (the ones included in our devices)
  • BMP085 pressure sensor

This is a screenshot of application monitoring the X and Y gyro-axis of the navigation board as well as the X-axis of the digital compass:

Sensmon-screen.png

Hacking

Since each ADC provices two channels and the gyroscope is 'only' triaxial, one channel is free for use. A wire can be soldered onto a tiny testpad or directly to the pin on the chip.

Personal tools

Preliminary Information. This page will be moved as soon as it contains the most important imformation about the board. (probably this weekend).

Freerunner Navigation Board

The Freerunner Navigation Board is a small PCB which can be mounted inside the case to extend the Freerunner with additional Hardware. The Board contains the triaxial digital compass chip HMC5843 from Honeywell and two gyroscope chips from InvenSense (IDG650, ISZ650) to provide a triaxial gyroscope solution.

Full schematics and layout files are available from chonyota.net/freerunner

Hardware details

The board can be connected to the I2C bus which is available on testpads around the debug connector.

The compass chip is directly connected to the I2C bus. The gyroscopes have an analog output which is digitized using a 16-bit A/D converter ADS1115 from Texas Instruments.

Additional features which were planned but are not implemented yet: The board contains the footprint to add an additional MSP430 microcontroller from TI. It would be used to control the offset compensation features of the gyroscopes, read their internal temperature sensors and switch them off when not used. Latter can actually be done using a GPIO line which is available at a testpoint H-TP1516.

Software support

Right now, this additional hardware is not supported out of the box, but there are some pieces of software available to demonstrate that the hardware actually works.

Drivers

Hardware drivers are available from gitorious.

Digital compass

A kernel driver is available to control the HMC5843 digital compass through sysfs entries. Vala hackers can use a vala library for easier access.

Gyroscope

The Gyroscopes need a driver for the ADCs which can be downloaded from the ADS1115 repository. Besides the kernel module, these chips can be accessed from userspace using the i2c-dev driver and a userspace library for easier access. Vala bindings are available.

End user software

A Vala-based sensor monitor developed by User:MicVM can be used to visualize the sensor values. The software is very experimental. You are using it at your own risk :)

The monitor has been developed in order to easily add arbitrary sensors as sources. The monitor uses GTK and Cairo for drawing the values and right now is quite slow on the GTA02. We are working on improving the refresh speed. Possibly with the same toolkit.

Except for the above mentioned sensors there have been written plugins for:

  • LIS302DL accelerometers (the ones included in our devices)
  • BMP085 pressure sensor

This is a screenshot of application monitoring the X and Y gyro-axis of the navigation board as well as the X-axis of the digital compass:

Sensmon-screen.png

Hacking

Since each ADC provices two channels and the gyroscope is 'only' triaxial, one channel is free for use. A wire can be soldered onto a tiny testpad or directly to the pin on the chip.