(→List of FSO resources: sorted and supplemented (please check it))
|Line 35:||Line 35:|
=== UsbHost ===
=== UsbHost ===
Unless this resource is enabled, you've no
Unless this resource is enabled, you've no .
=== WiFi ===
=== WiFi ===
Revision as of 12:29, 12 December 2009
Resource management conception
Here goes some introductory text shamelessly borrowed from FSO specs.
One of the most important aspects of middleware for mobile devices is saving energy. To do this, the system needs to make sure that peripherals are only powered when they are actually in use by at least one application. In order to support multiple concurrent applications, it is not possible to leave peripheral control up to individual applications — otherwise one application could shut down e.g. a GPS receiver, while another application still wants to access it.
FSO introduces the concept of resources. A resource is a high-level entity with a name and a state. The name is used to identify a resource (e.g. WiFi), the state is describing its condition (e.g. enabled). It is important to understand that a resource not necessarily correlates to a peripheral device. Although enabling a resource such as Bluetooth most likely has the consequence of powering up a device, there may as well be more to it, such as launching a low level device handling services or allocating related resources.
Once in a while, reference counted handling of resources gets in your way, for example when you are running legacy applications or want to configure or debug peripherals. In that case it may become necessary for a resource to be always enabled or always disabled. While not recommended, it is possible to switch from automatic resource control to manual control by calling SetResourcePolicy. Valid values are auto (which is the default on system startup), enabled, and disabled.
List of FSO resources
Unless this resource is enabled, the module is unpowered.
You need to have this resource requested, to have bluetooth module powered.
Default rules.yaml checks for this resource, to disable automatic suspend, when it's requested.
While this resource is kept, the display won't be blanked.
Same idea as WiFi/Bluetooth
The same for GSM modem
A test resource
Unless this resource is enabled, you've no usb host.
Unless this resource is enabled you've no eth0 and wifi module is completely unpowered.
By default, the policy for every resource is auto, which means that it is enabled only when it has been requested by a currently running application. However, it is possible to throw a "hard switch" to force the resource to be always enabled or disabled, regardless of what applications request it. This can be done with the help of the SHR Settings GUI or from the command line using an appropriate mdbus call. For example,
mdbus -s org.freesmartphone.ousaged /org/freesmartphone/Usage \ org.freesmartphone.Usage.SetResourcePolicy Bluetooth enabled
Do not forget that forcing a resource to be enabled will drain more power since it will leave the corresponding device powered all the time. And, of course, forcing a resource to be disabled will cause any applications that require it to fail. Because of this, you are highly discouraged from changing the resource policy from auto unless you know exactly what you are doing.
fsoraw (created per Joerg's request ) utility. With it you can automatically request the necessary resource before starting a command and release it when it's finished (this will happen even if it was killed with SIGKILL).
Typical basic use:
fsoraw -r CPU,Display mokomaze
Start a game (or any other app) and avoid auto-suspend and display-blank
Especially recommended for WiFi since due to the bugs in the firmware and the driver full power-cycle of the module is often advantageous.
Example command (works for open, WEP and WPA/WPA2 networks, automatically determining the network it can connect to, just add all the networks you use to the config):
fsoraw -r WiFi -- wpa_supplicant -ieth0 -Dwext -c/etc/wpa_supplicant/wpa_supplicant.conf
To keep wifi useable, due to bug still present currently (2009-08-18) you need to also do (fixed with the latest SHR kernel, 2009-09-01, this command is no longer needed):
rmmod ar6000 && modprobe ar6000
Bluetooth scan for nearby devices example:
fsoraw -r Bluetooth -- bash -c "sleep 1; hcitool scan"
It would be nice to have a command to list the current state of all resources. (See .) Unfortunately, such a utility is yet to be written. However, a first take on implementing the desired functionality can already be downloaded from .
To examine the state of a resource manually, there are three
org.freesmartphone.Usage methods which are particularly useful.
- GetResourcePolicy ( s ) → s
- Get the current resource policy for a given resource.
- GetResourceState ( s ) → b
- Get the current resource state. True if the resource is currently enabled.
- GetResourceUsers ( s ) → as
- Get the users (an array of bus names) which currently use a given resource.
mdbus -s org.freesmartphone.ousaged /org/freesmartphone/Usage \ org.freesmartphone.Usage.GetResourceState WiFi