|WARNING: Dfu-util is currently broken on big-endian architectures|
|WARNING: Do not flash U-Boot unless you are sure you need to|
|NOTE: You need to connect your neo directly to your pc with no hub between. Otherwise there could be problems with the hub and the usb reset.|
dfu-util is a program that implements the Host (PC) side of the USB DFU (Universal Serial Bus Device Firmware Upgrade) protocol.
In the OpenMoko project, we use this program to communicate with our specially enhanced u-boot boot loader, which implements the DFU device side.
Using dfu-util and your Neo1973, you can Link* transfer and flash partitions to NAND Flash, such as
- transfer anything into Neo1973 RAM
- this can be used for fast development cycles of low-level code such as kernels without flashing them
- read out the current NAND partitions
- this is an easy and efficient way of doing full backups of your phone
dfu-util can be found at http://svn.openmoko.org/trunk/src/host/dfu-util/
Binary packages will be made available as part of the regular OpenMoko builds
dfu-util - (C) 2007 by OpenMoko Inc. This program is Free Software and has ABSOLUTELY NO WARRANTY Usage: dfu-util [options] ... -h --help Print this help message -V --version Print the version number -l --list List the currently attached DFU capable USB devices -d --device vendor:product Specify Vendor/Product ID of DFU device -c --cfg config_nr Specify the Configuration of DFU device -i --intf intf_nr Specify the DFU Interface number -a --alt alt_nr Specify the Altseting of the DFU Interface -t --transfer-size Specify the number of bytes per USB Transfer -U --upload file Read firmware from device into <file> -D --download file Write firmware from <file> into device -R --reset Issue USB Reset signalling once we're finished
Using the --list option, you can list the available DFU capable devices, their configuration, interface and altsettings. Below is an example for a current Neo1973 phone in u-boot Runtime Mode
# ./dfu-util --list dfu-util - (C) 2007 by OpenMoko Inc. This program is Free Software and has ABSOLUTELY NO WARRANTY Found DFU Runtime: [0x1457:0x5119] devnum=0, cfg=0, intf=2, alt=0, name="USB Device Firmware Upgrade"
Below is an example for a current Neo1973 phone in u-boot DFU Mode
# ./dfu-util --list dfu-util - (C) 2007 by OpenMoko Inc. This program is Free Software and has ABSOLUTELY NO WARRANTY Found DFU: [0x1457:0x5119] devnum=16, cfg=0, intf=0, alt=0, name="RAM 0x32000000" Found DFU: [0x1457:0x5119] devnum=16, cfg=0, intf=0, alt=1, name="u-boot" Found DFU: [0x1457:0x5119] devnum=16, cfg=0, intf=0, alt=2, name="u-boot_env" Found DFU: [0x1457:0x5119] devnum=16, cfg=0, intf=0, alt=3, name="kernel" Found DFU: [0x1457:0x5119] devnum=16, cfg=0, intf=0, alt=4, name="splash" Found DFU: [0x1457:0x5119] devnum=16, cfg=0, intf=0, alt=5, name="rootfs"
This shows you six interfaces, all in configuration 0 and interface 0, with altsetting 0...4. The name is currently not yet defined, but will be added to one of the upcoming u-boot releases. The mapping on the Neo1973 is as follows:
- 0: RAM
- 1: 'u-boot' partition
- 2: 'u-boot_env' partition
- 3: 'kernel' partition
- 4: 'splash' partition
- 5: 'rootfs' partition
You can specify the USB Vendor and Product ID of the device you want to program:
dfu-util --device 0x1457:0x5119
If you only have one standards-compliant DFU device attached to your PC, this is optional. However, as soon as you have multiple DFU devices, dfu-util will detect this and abort, asking you to specify which device it shall use.
Specifies the size of each individual USB transfer. If you don't use it, the maximum possible size for your combination of host operating system and USB device is chosen (for optimal performance).
download the given file into the device.
upload from the DFU device into the given file[name].
|NOTE: Upload support is currently broken|
There's no full-fledged manual yet. Instead, some examples:
Flashing the kernel
dfu-util -a 3 -R -D /path/to/uImage
Flashing the bootloader
dfu-util -a 1 -R -D /path/to/u-boot.bin
Copying a kernel into RAM
dfu-util -a 0 -R -D /path/to/uImage
Once this has finished, the kernel will be available at the default load address of 0x32000000 in Neo1973 RAM.
|NOTE: You cannot transfer more than 2MB of data into RAM using this method|
If during flashing of an image using dfu-util you're consistently getting an error -110 message, check that the size of the destination NAND partition is big enough to hold the image. For example the kernel partition is only 2 MB big by default and a kernel with debugging info compiled-in can often exceed this. It's possible to change the partition layout to enlarge a given partition and shrink other partitions but you have to remember to reflash all partitions whose start offset has changed afterwards. To adjust partitions layout use the mtdparts u-boot command.
If in turn you're facing errors in seemingly random places during the flashing of images, most likely the USB hub or cable through which your Neo1973 is connected, is of too poor quality. It is recommended that you always connect the phone directly to the host when using dfu-util.If dfu-util reports a message like the following, before it starts flashing:
Resetting USB... not at least 2 device changes found ?!? Lost device after RESET?retry the command - it should work on a second run.
- Compiling dfu-util on Mac: http://lists.openmoko.org/pipermail/community/2007-July/008438.html
Flashing openmoko to the latest software.
English • العربية • Български • Česky • Dansk • Deutsch • Esperanto • Eesti • Español • فارسی • Suomi • Français • עברית • Magyar • Italiano • 한국어 • Nederlands • Norsk (bokmål) • Polski • Português • Română • Русский • Svenska • Slovenčina • Українська • 中文(中国大陆) • 中文(台灣) • Euskara • Català